參數資料
型號: G768D
英文描述: ± 3oC remote thermal sensor with one fan control and SMBus interface.|Thermal Sensor / Detector Series
中文描述: ± 3oC遠程溫度傳感器一個風扇控制和SMBus接口。|熱傳感器/探測器系列
文件頁數: 11/16頁
文件大?。?/td> 323K
代理商: G768D
Ver: 1.4
May 23, 2003
TEL: 886-3-5788833
http://www.gmt.com.tw
11
G768D
Global Mixed-mode Technology Inc.
If the remote channel is shorted (DXP to DXN or DXP
to GND), the ADC reads 0000 0000 so as not to trip
either the THIGH or TLOW alarms at their POR set-
tings. In applications that are never subjected to 0°C in
normal operation, a 0000 0000 result can be checked
to indicate a fault condition in which DXP is acciden-
tally short circuited. Similarly, if DXP is short circuited
to V
CC
, the ADC reads +127°C for both channels, and
the device alarms.
ALERT Interrupts
The ALERT interrupt output signal is latched and can
only be cleared by reading the Alert Response ad-
dress. Interrupts are generated in response to THIGH
and TLOW comparisons and when the remote diode is
disconnected (for continuity fault detection). The in-
terrupt does not halt automatic conversions; new tem-
perature data continues to be available over the SMBus
interface after ALERT is asserted. The interrupt output
rupt output pin is open-drain so that device can share
a common interrupt line. The interrupt rate can never
exceed the conversion rate.
The interface responds to the SMBus Alert Response
address, an interrupt pointer return-address feature
(see Alert Response Address section). Prior to taking
corrective action, always check to ensure that an in-
terrupt is valid by reading the current temperature.
Alert Response Address
The SMBus Alert Response interrupt pointer provides
quick fault identification for simple slave devices that
lack the complex, expensive logic needed to be a bus
master. Upon receiving an ALERT interrupt signal, the
host master can broadcast a Receive Byte transmission
to the Alert Response slave address (0001 100). Then
any slave device that generated an interrupt attempts to
identify itself by putting its own address on the bus.
Table 4. Command-Byte Bit Assignments
REGISTER
RRTE2
RRTE1
RSL
RCL
RCRA
RRHI2
RRLS2
RRHI1
RRLS1
WCA
WCRW
WRHA2
WRLN2
WRHA1
WRLN1
OSHT
SET_CNT1
ACT_CNT1
FAN_STA1
TMAX1
THYST1
TMAX2
THYST2
TCRIT1
TCRIT2
COMMAND
00h
01h
02h
03h
04h
05h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Dh
0Eh
0Fh
10h
11h
12h
31h
32h
33h
34h
35h
36h
POR STATE
0000 0000b
0000 0000b
N/A
0000 0000b
0000 0010b
0111 1111b (127) Read 2nd remote THIGH limit
1100 1001b(-55) Read 2nd remote TLOW limit
0111 1111b (127) Read 1st remote THIGH limit
1100 1001b (-55) Read 1st remote TLOW limit
N/A
Write configuration byte
N/A
Write conversion rate byte
N/A
Write 2nd remote THIGH limit
N/A
Write 2nd remote TLOW limit
N/A
Write 1st remote THIGH limit
N/A
Write 1st remote TLOW limit
N/A
One-shot command (use send-byte format)
1111 1111b
Write 1st fan programmed speed register
1111 1111b
Read 1st fan actual speed register
10b
Read 1st fan status register
0100 0110b (70)
1st remote TMAX
0011 1100b (60)
1st remote THYST
0100 0110b (70)
2nd remote TMAX
0011 1100b (60)
2nd remote THYST
0110 1100b (108) Critical temperature for 1
st
remote temperaure sensor
0101 1000b (88)
Critical temperature for 2
nd
remote temperaure sensor
FUNCTION
Read 2nd remote temperature: returns latest temperature
Read 1st remote temperature: returns latest temperature
Read status byte (flags, busy signal)
Read configuration byte
Read conversion rate byte
相關PDF資料
PDF描述
G7881 Optoelectronic
G8342 Optoelectronic
G8796 Optoelectronic
G7J-2A2B-B
G7J-2A2B-P
相關代理商/技術參數
參數描述
G770127-1 REV D 制造商:Amphenol Corporation 功能描述:AMPHENOL CANADA - Rail/Tube
G770140-1 REV E 制造商:Amphenol Corporation 功能描述:AMPHENOL CANADA - Rail/Tube
G77015 制造商:Glenair Inc 功能描述:1 REPLACEMENT PAD for TG69P
G771 制造商:GMT 制造商全稱:Global Mixed-mode Technology Inc 功能描述:Two Remote Temperature Sensors with SMBus Serial Interface and System Reset Circuit
G772203-1 REV C 制造商:International Rectifier 功能描述:G772203-1 REV C - Bulk