- 您現在的位置：買賣IC網 > PDF目錄384300 > G5Y-1-H (Omron Electronics LLC) Low Signal Relay PDF資料下載
參數資料
| 型號： | G5Y-1-H |
| 廠商： | Omron Electronics LLC |
| 英文描述： | Low Signal Relay |
| 中文描述： | 低信號繼電器 |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 181K |
| 代理商： | G5Y-1-H |
6
G5Y-1
G5Y-1
I
MICROSTRIPS
For high-frequency transmission circuits, the use of
microstrips is recommended. By adopting this stripline
method, a low-loss transmission circuit can be configured. The
microstrips are prepared by etching a PC board made of
dielectric material and covered on both sides with copper foil.
As shown in the figure below, the microstrip utilizes the
concentration of the electric field between transmission line
and the ground.
The characteristic impedance of a transmission line is
determined by the type of PC board (specific inductive
capacity), its thickness, and the width of the transmission line.
This impedance is expressed by the following formula.
where
w: Width of transmission line
e
r: Relative dielectric constant
e
r
h: Thickness of dielectric PC board, provided that the
thickness of copper foil is no greater than h.
This relationship is shown the the figure below.
For example, when a 50
transmission line is to be formed
using a 1.6 mm (0.06) glass epoxy type double-sided PC
board, the width of the transmission line can be obtained in
the following manner. Since the specific inductive capacity (
e
r)
of this circuit board is 4.8, w/h = 1.7 (obtained from the above
table). Based on the thickness of the PC board (e.g., 1.6 mm
[0.06]), the thickness of transmission line w can be calculated
as follows.
w = h x 1.7 = 1.6 (0.06) x 1.7
～
2.7 mm (0.11 in)
Note that in this calculation, the thickness of copper foil “t” is
ignored, so there may be a greater error in characteristic
impedance of t
～
w. Also, the attenuation constant of the
transmission line, due to the effective filling rate of microstrip
or dielectric loss and conductor loss, is not taken into account,
but these factors must be considered in the actual design of
microstrips. In the frequency band for which Model G5Y is
intended, however, these factors may be ignored by
shortening the length of the transmission line.
Bending of strip transmission line
Shape of land
1. The land section should be on the center line of the copper-
foil pattern so that the soldered fillets become uniform.
2. If the relay and other circuit components are to be soldered
manually after the automatic soldering of the PC board, a
terminal hole can be secured by providing a break in the
land.
Conductor width and microstrip
Patterns for DC circuits
The following thicknesses of copper foil are standard: 35
μ
m
(1.38 mil) and 70
μ
m (2.76 mil). The conductor width is
determined by the carry current and allowable temperature
rise. Refer to the table on the following page.
Conductor width and carry current
(according to IEC Pub321)
相關PDF資料 |
PDF描述 |
|---|---|
| G8SE | Sub-Miniature Automotive PCB Relay |
| G8SE-1A4-L12DC | Sub-Miniature Automotive PCB Relay |
| GA1A3Q | MEDIUM SPEED SWITCHING RESISTOR BUILT-IN TYPE NPN TRANSISTOR |
| GA1A4M-T1 | MEDIUM SPEED SWITCHING RESISTOR BUILT-IN TYPE NPN TRANSISTOR |
| GA1A4M | MEDIUM SPEED SWITCHING RESISTOR BUILT-IN TYPE NPN TRANSISTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| G5Y1H12VDC | 制造商:OMRON 功能描述:* |
| G5Y-1-H-DC12 | 功能描述:低信號繼電器 - PCB 200MW 12V 720 OHM RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
| G5Y1HDC24 | 制造商:Ormon 功能描述:RELAY |
| G5Y-1-H-DC24 | 制造商:Ormon 功能描述:RELAY |
| G5Y1HDC5 | 制造商:Omron Corporation 功能描述:RELAY RF SPDT 10MA 5V |
發布緊急采購，3分鐘左右您將得到回復。