- 您現在的位置：買賣IC網 > PDF目錄384300 > G5Y-1-H (Omron Electronics LLC) Low Signal Relay PDF資料下載
參數資料
| 型號： | G5Y-1-H |
| 廠商： | Omron Electronics LLC |
| 英文描述： | Low Signal Relay |
| 中文描述： | 低信號繼電器 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 181K |
| 代理商： | G5Y-1-H |
5
G5Y-1
G5Y-1
Unit: mm (inch)
Terminal arrangement/
Internal connections
(bottom view)
Mounting holes
(bottom view)
Dimensions
I
PC BOARD SELECTION
Thickness of PC board
PC boards are generally available in the following
thicknesses: 0.8 (0.03), 1.0 (0.04), 1.2 (0.05), 1.6 (0.06), and
2.0 mm (0.08 in). In determining the thickness of the PC
board to be used, the pattern widths of the microstrips must
be taken into account. First, determine the applicable pattern
widths based on the intended arrangement of components on
the PC board. Then select the appropriate PC board
thickness.
PC board material
The base materials of PC boards can be divided into two
types: epoxy type and phenolic type. For high-frequency
circuits, glass epoxy type double-sided PC boards are
recommended because of their distinct dielectric constant
and material stability. However, paper epoxy type or paper
phenolic type single-sided PC boards may also be used if
cost factor is essential. Refer to “Examples of packaging
design” for mounting the relay on a single-sided PC board.
I
PATTERN DESIGN
Preparation for pattern design
Relay mounting direction
The mounting direction of each relay must be taken into
account for the relay to function with maximum performance.
Shock resistance is one of the representative relay
performance characteristics greatly influenced by the relay
mounting direction. Refer to the Shock Resistance
Characteristic in “Characteristic Data” section.
Note that the shock resistance of a relay (NC contact), with its
coil in the nonenergized state, is governed greatly by the
mounting direction of the relay.
How to design PC Board
Terminal hole diameters, land diameters, and land shapes
(DC circuit)
Terminal hole diameter and land diameter
Select the appropriate terminal hole diameter and land
diameter from the following table based on the PC board
mounting hole drawing. Land diameters may be reduced to
less than those listed below if thru-hole connection process is
to be employed.
Terminal hole diameters and land diameters
Unit: mm (inch)
I
RELAY
Hints on Correct Use
Terminal hole
diameter
Nominal value
0.6 (0.02)
0.8 (0.03)
1.0 (0.04)
1.2 (0.05)
1.3 (0.05)
1.5 (0.06)
1.6 (0.06)
2.0 (0.08)
Minimum
land
diameter
1.5 (0.06)
1.8 (0.07)
2.0 (0.08)
2.5 (0.10)
Tolerance
±
0.1 (
±
0.004)
3.0 (0.12)
Note:
Parts marked with and indicate mounting direction mark on G5Y relay.
12345
12345
相關PDF資料 |
PDF描述 |
|---|---|
| G8SE | Sub-Miniature Automotive PCB Relay |
| G8SE-1A4-L12DC | Sub-Miniature Automotive PCB Relay |
| GA1A3Q | MEDIUM SPEED SWITCHING RESISTOR BUILT-IN TYPE NPN TRANSISTOR |
| GA1A4M-T1 | MEDIUM SPEED SWITCHING RESISTOR BUILT-IN TYPE NPN TRANSISTOR |
| GA1A4M | MEDIUM SPEED SWITCHING RESISTOR BUILT-IN TYPE NPN TRANSISTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| G5Y1H12VDC | 制造商:OMRON 功能描述:* |
| G5Y-1-H-DC12 | 功能描述:低信號繼電器 - PCB 200MW 12V 720 OHM RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
| G5Y1HDC24 | 制造商:Ormon 功能描述:RELAY |
| G5Y-1-H-DC24 | 制造商:Ormon 功能描述:RELAY |
| G5Y1HDC5 | 制造商:Omron Corporation 功能描述:RELAY RF SPDT 10MA 5V |
發布緊急采購，3分鐘左右您將得到回復。