- 您現在的位置：買賣IC網 > PDF目錄375989 > FW82801E (Intel Corp.) Intel 82801E Communications I/O Controller Hub (C-ICH) PDF資料下載
參數資料
| 型號： | FW82801E |
| 廠商： | Intel Corp. |
| 英文描述： | Intel 82801E Communications I/O Controller Hub (C-ICH) |
| 中文描述： | 英特爾82801E通訊I / O控制器集線器（丙，出血） |
| 文件頁數： | 31/84頁 |
| 文件大小： | 1196K |
| 代理商： | FW82801E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
Intel
82801E C-ICH
Advance Information Datasheet
31
PIRQ[E:F]#
PIRQ[G]#/GPIO[4]
PIRQ[H]#/GPIO[5]
I/OD
PCI Interrupt Requests:
In Non-APIC Mode the PIRQx# signals can be
routed to interrupts 3:7, 9:12, 14 or 15 as described in the Interrupt Steering
section. Each PIRQx# line has a separate Route Control Register.
In APIC mode, these signals are connected to the internal I/O APIC in the
following fashion: PIRQ[E]# is connected to IRQ20, PIRQ[F]# to IRQ21,
PIRQ[G]# to IRQ22, and PIRQ[H]# to IRQ23. If not needed for interrupts,
these signals can be used as GPIO.
PLOCK#
I/O
PCI Lock:
PLOCK# indicates an exclusive bus operation and may require
multiple transactions to complete. 82801E C-ICH asserts PLOCK# when it
performs non-exclusive transactions on the PCI bus.
PWROK
I
Power OK:
When asserted, PWROK is an indication to the 82801E C-ICH
that core power and PCICLK have been stable for at least 1 ms. PWROK can
be driven asynchronously. When PWROK is negated, the 82801E C-ICH
asserts PCIRST#.
RCIN#
I
Keyboard Controller Reset Processor:
The keyboard controller can
generate INIT# to the processor. This saves the external OR gate with the
82801E C-ICH’s other sources of INIT#. When the 82801E C-ICH detects the
assertion of this signal, INIT# is generated for 16 PCI clocks.
REQ[3:0]#
REQ[5]#
/REQ[B]#
/GPIO[1]
I
PCI Requests:
The 82801E C-ICH supports up to four masters on the PCI
bus. REQ[5]# is muxed with PC/PCI REQ[B]# (must choose one or the other,
but not both). If not used for PCI or PC/PCI, REQ[5]#/REQ[B]# can instead be
used as GPIO[1].
NOTE:
REQ[0]# is programmable to have improved arbitration latency for
supporting PCI-based 1394 controllers.
REQ[A]#
/GPIO[0]
REQ[B]#
/REQ[5]#
/GPIO[1]
I
PC/PCI DMA Request [A:B]:
This request serializes ISA-like DMA Requests
for the purpose of running ISA-compatible DMA cycles over the PCI bus. This
is used by devices such as PCI-based Super I/O or audio codecs that need to
perform legacy 8237 DMA but have no ISA bus.
When not used for PC/PCI requests, these signals can be used as General
Purpose Inputs. Instead, REQ[B]# can be used as the fourth PCI bus request.
RESERVED1
RESERVED2
—
This signal must have an external pull up to Vcc3_3.
RI#
I
Ring Indicate:
From the modem interface. This signal can be enabled as a
wake event; this is preserved across power failures.
RSM_PWROK
I
Resume Well Power OK:
When asserted, this signal is an indication to the
82801E C-ICH that the resume well power has been stable for at least 10 ms.
NOTE:
The 82801E C-ICH does not use the Resume Well Power OK signal.
RSMRST#
I
Resume Well Reset:
RSMRST# is used for resetting the resume power
plane logic.
NOTE:
The 82801E C-ICH does not use the Resume Well Reset signal.
RTCRST#
I
RTC Reset:
When asserted, this signal resets register bits in the RTC well
and sets the RTC_PWR_STS bit (bit 2 in GEN_PMCON3 register). This
signal is also used to enter the test modes documented in “Test Signals” on
page 49.
NOTE:
Clearing CMOS in an 82801E C-ICH-based platform can be done by
using a jumper on RTCRST# or GPI, or using SAFEMODE strap.
Implementations should not attempt to clear CMOS by using a
jumper to pull VccRTC low.
RTCX1
Special
Crystal Input 1:
This signal is connected to the 32.768 KHz crystal. If no
external crystal is used, then RTCX1 can be driven with the desired clock
rate.
RTCX2
Special
Crystal Input 2:
This signal is connected to the 32.768 KHz crystal. If no
external crystal is used, then RTCX2 should be left floating.
Table 6. 82801E C-ICH Signal Description (Sheet 7 of 11)
Signal
Type
Description
相關PDF資料 |
PDF描述 |
|---|---|
| FWB150 | 1.5 AMP FAST RECOVERY BRIDGE RECTIFIERS |
| FWB151 | 1.5 AMP FAST RECOVERY BRIDGE RECTIFIERS |
| FWB1510 | 1.5 AMP FAST RECOVERY BRIDGE RECTIFIERS |
| FWB152 | 1.5 AMP FAST RECOVERY BRIDGE RECTIFIERS |
| FWB154 | 1.5 AMP FAST RECOVERY BRIDGE RECTIFIERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FW82801E S L5AW | 制造商:Intel 功能描述:I/O Controller Phase Controller 421-Pin BGA |
| FW82801EB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| FW82801EB S L6TN | 制造商:Intel 功能描述:CONTROLLER: IO CONTROLLER |
| FW82801EB S L73Z | 制造商:Intel 功能描述:I/O Controller Phase Controller 460-Pin BGA |
| FW82801ER | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。