參數資料
型號: FT4232HQ-REEL
廠商: FTDI, Future Technology Devices International Ltd
文件頁數: 13/45頁
文件大?。?/td> 0K
描述: IC USB HS QUAD UART/SYNC 64-QFN
標準包裝: 1
系列: USBmadeEZ-FIFO
特點: USB 至 UART 和(或)SPI、I2C、JTAG
通道數: 4,QUART
FIFO's: 2048 字節
規程: RS232,RS422,RS485
電源電壓: 3 V ~ 3.6 V
帶自動流量控制功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 64-VFQFN 裸露焊盤
供應商設備封裝: 64-QFN 裸露焊盤(9x9)
包裝: 標準包裝
產品目錄頁面: 634 (CN2011-ZH PDF)
配用: 768-1031-ND - MOD USB HS FT4232H EVAL
其它名稱: 768-1027-6
Copyright 2010 Future Technology Devices International Limited
20
Document No.: FT_000060
FT4232H QUAD HIGH SPEED USB TO MULTIPURPOSE UART/MPSSE IC
Datasheet Version 2.2
Clearance No.: FTDI#78
4.4 MPSSE Interface Mode Description.
MPSSE Mode is designed to allow the FT4232H to interface efficiently with synchronous serial protocols
such as JTAG, I2C and SPI Bus. It can also be used to program SRAM based FPGA’s over USB. The
MPSSE interface is designed to be flexible so that it can be configured to allow any synchronous serial
protocol (industry standard or proprietary) to be implemented using the FT4232H. MPSSE is only
available on channel A and channel B.
MPSSE is fully configurable, and is programmed by sending commands down the data stream. These can
be sent individually or more efficiently in packets. MPSSE is capable of a maximum sustained data rate of
30 Mbits/s.
When a channel is configured in MPSSE mode, the IO timing and signals used are shown in Figure 4.4
and Table 4.1. These show timings for CLKOUT=30MHz. CLKOUT can be divided internally to be provide a
slower clock.
Figure 4.4 MPSSE Signal Waveforms
NAME
MIN
NOM
MAX
Units
COMMENT
t1
33.33
ns
CLKOUT period
t2
15
16.67
ns
CLKOUT high period
t3
15
16.67
ns
CLKOUT low period
t4
1
7.15
ns
CLKOUT to TDI/DO delay
t5
0
ns
TDO/DI hold time
t6
11
TDO/DI setup time
Table 4.1 MPSSE Signal Timings
MPSSE mode is enabled using Set Bit Bang Mode driver command. A hex value of 2 will enable it, and a
hex value of 0 will reset the device. See application note AN2232L-02, “Bit Mode Functions for the
FT2232D” for more details and examples.
The MPSSE command set is fully described in application note AN_108 – “Command Processor For
MPSSE and MCU Host Bus Emulation Modes”.
The following additional application notes are available for configuring the MPSSE :
AN_109 – “Programming Guide for High Speed FTCI2C DLL”
AN_110 – “Programming Guide for High Speed FTCJTAG DLL”
AN_111 – “Programming Guide for High Speed FTCSPI DLL”
相關PDF資料
PDF描述
FUSB1500MHX IC USB 2.0 TRANSCEIVER 16-MLP
FUSB2805MLX TXRX USB2.0 HS OTG ULPI 32MLP
FXLA2203UMX TRANSLATOR LEVEL DUAL 24UMLP
GAL16V8D-15LJN SPLD 62.5MHZ EECMOS 20 PLCC
GAL18V10B-20LP IC GAL 10OUT MACROCELL 7.5NS 20
相關代理商/技術參數
參數描述
FT4232HQ-TRAY 功能描述:USB 接口集成電路 USB HS to Quad UART/ SPI/JTAG/I2C QFN-64 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
FT-42-3T 制造商:PANASONIC INDUSTRIAL AUTOMATION SALES 功能描述:FIBER M4 THRUBEAM R4 BEND RADIUS 制造商:Panasonic Electric Works 功能描述:Fiber, M4, Thru-beam, 3M Free cut, R4 Bend radius
FT-42S 制造商:PANASONIC INDUSTRIAL AUTOMATION SALES 功能描述:FIBER M4 THREADED THRUBEAM R4 制造商:Panasonic Electric Works 功能描述:SENSOR, FIBRE OPTIC, THRUBEAM, 1.13M; Fiber Optic Sensor Type:Thrubeam; Sensing Range Max:1.13m; Sensing Range:0m to 1.13m
FT-42W 制造商:PANASONIC INDUSTRIAL AUTOMATION SALES 功能描述:FIBER M4 THREADED THRUBEAM R1 制造商:Panasonic Electric Works 功能描述:SENSOR, FIBRE OPTIC, THRUBEAM, 800MM; Fiber Optic Sensor Type:Thrubeam; Sensing Range Max:800mm; Sensing Range:0mm to 800mm
FT-43 制造商:PANASONIC ELECTRIC WORKS ACSD 功能描述:Sensor, M4 Threaded Thru Beam, R4, 2m Cable 制造商:Panasonic Electric Works 功能描述:SENSOR FIBRE OPTIC THRUBEAM 1.4M 制造商:Panasonic Electric Works 功能描述:SENSOR, FIBRE OPTIC, THRUBEAM, 1.4M 制造商:Panasonic Electric Works 功能描述:SENSOR, FIBRE OPTIC, THRUBEAM, 1.4M; Fiber Optic Sensor Type:Thrubeam; Sensing Range Max:1.4m; Sensing Range:0m to 1.4m