參數資料
型號： FT232HL-REEL
廠商： FTDI, Future Technology Devices International Ltd
文件頁數： 29/65頁
文件大?。?/td> 0K
描述： IC HS USB TO UART/FIFO 48LQFP
應用說明： FT1248 Application Note
標準包裝： 1
通道數： 1，UART
FIFO's： 4kb
規程： RS232，RS422，RS485
電源電壓： 1.62 V ~ 1.98 V，2.97 V ~ 3.63 V
帶并行端口： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
安裝類型： 表面貼裝
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 標準包裝
其它名稱： 768-1101-6
Copyright 2012 Future Technology Devices International Limited
35
Document No.: FT_000288
FT232H SINGLE CHANNEL HI-SPEED USB TO MULTIPURPOSE UART/FIFO IC
Datasheet Version 1.8
Clearance No.: FTDI #199
WRSTB#
RDSTB#
Figure 4.12 Synchronous Bit-Bang Mode Timing Interface Example
WRSTB# = this output indicates when new data has been written to the I/O pins from the Host PC (via
the USB interface).
Name
Description
t1
Current pin state is read
t2
RDSTB# is set inactive and data on the parallel I/O pins is read and sent to the
USB host.
T3
RDSTB# is set active again, and any pins that are output will change to their
new data
t4
1 clock cycle to allow for data setup
t5
WRSTB# goes active. This indicates that the host PC has written new data to
the I/O parallel data pins
t6
WRSTB# goes inactive
Table 4.3 Synchronous Bit-Bang Mode Timing Interface Example Timings
RDSTB# = this output rising edge indicates when data has been read from the I/O pins and sent to the
Host PC (via the USB interface).
The WRSTB# goes active in t5. The WRSTB# goes active when data is read from the USB RXFIFO (i.e.
sent from the PC). The RDSTB# goes inactive when data is sampled from the pins and written to the USB
TXFIFO (i.e. sent to the PC). The SETUP command to the FT232H is used to setup the bit-mode. This
command also contains a byte wide data mask to set the direction of each bit. The direction on each pin
doesn’t change unless a new SETUP command is used to modify the direction.
The WRSTB# and RDSTB# strobes are only a guide to what may be happening depending on the
direction of the bus. For example if all pins are configured as inputs, it is still necessary to write to these
pins in order to get the FT232H to read those pins even though the data written will never appear on the
pins.
Signals and data-flow are illustrated in Figure 4.13
USB Rx
FIFO/
Buffer
Parallel I/O
data
Parallel
I/O pins
USB
WRSTB#
RDSTB#
USB Tx
FIFO/
Buffer
Figure 4.13 Bit-bang Mode Dataflow Illustration Diagram.
相關PDF資料
PDF描述
FT232RL-REEL IC USB FS SERIAL UART 28-SSOP
FT245BL-REEL IC USB FS PARALLEL FIFO 32-LQFP
FT245RL-REEL IC USB TO PARALLEL FIFO 28-SSOP
FT4232HQ-REEL IC USB HS QUAD UART/SYNC 64-QFN
FUSB1500MHX IC USB 2.0 TRANSCEIVER 16-MLP
相關代理商/技術參數
參數描述
FT232HL-TRAY 功能描述:USB 接口集成電路 USB HS to UART/FIFO SPI/JTAG/I2C LQFP-48 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
FT232HQ-REEL 功能描述:USB 接口集成電路 USB HS to UART/FIFO SPI/JTAG/I2C QFN-48 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
FT232HQ-TRAY 功能描述:USB 接口集成電路 USB HS to UART/FIFO SPI/JTAG/I2C QFN-48 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
FT232R 制造商:FTDI 制造商全稱:FTDI 功能描述:USB UART IC - Single chip USB to asynchronous serial data transfer interface
FT232R_10 制造商:FTDI 制造商全稱:FTDI 功能描述:USB UART IC - Single chip USB to asynchronous serial data transfer interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*