- 您現在的位置：買賣IC網 > PDF目錄375797 > FIC03272 (Electronic Theatre Controls, Inc.) Microprocessor for handling signals from the TGS4161 carbon dioxide sensor PDF資料下載
參數資料
| 型號： | FIC03272 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Microprocessor for handling signals from the TGS4161 carbon dioxide sensor |
| 中文描述： | 微處理器處理的TGS4161二氧化碳傳感器信號 |
| 文件頁數： | 3/14頁 |
| 文件大?。?/td> | 366K |
| 代理商： | FIC03272 |
Revised 06/04
3
TECHNICAL INFORMATION FOR FIC03272
1-3
Two output signals
FIC03272 generates two separate output signals:
a) For calculating CO
2
concentrations, a pulse width
modulated (PWM) signal is output.
b) An On/Off signal is generated as a control signal
for devices such as ventilation fans, dampers, etc.
Notes:
1) The microprocessor is designed to assume the
highest value of EMF reading is representative of
400ppm of CO
2
(ambient air levels). As a result, an
accurate reading cannot be expected if the sensor is
used in an environment where CO
2
constantly exists
at higher concentrations than can be found in a
normal clean environment.
2) This device is not suitable for usage in life saving
equipment.
2. Basic Functions
2-1
Initial setting of operational conditions
In order to achieve optimal performance of the sensor,
manual preset of operational conditions is provided.
2-2
Automatic operation
Once power is supplied, an initial warm-up timer is
activated. When the initial warm-up time is finished,
the microprocessor will automatically begin
operation and commence generating the two output
signals mentioned above.
2-3
Line test
The microprocessor has the ability to perform a line
test for checking the functionality of the
microprocessor and the surrounding circuits. This
allows users to eliminate tool testing which is
normally done on the production line after assembly.
3. Pin Arrangement
Pin arrangement of FIC03272 is shown in Figure 1.
4. Pin Functions
The basic pin functions of FIC03272 are shown in
Table 1 (
shown on Page 4
).
4-1
Pins for the initial setting of operational conditions
To optimize sensor performance, the following pins
are provided for setting operational conditions at the
time of power-on. No change can be made to
operational conditions after the initial setting without
powering off and then repowering the device.
4-1-1
Input signal for setting the sensor’s initial warm-
up time (Pin No. 10)
Initial warm-up time, which is necessary to stabilize
the sensor’s output signal after an unpowered period,
is set by input of a signal to port R43 (see Table 2).
No signal can be taken from the microprocessor’s
output ports during initial warm-up time.
4-1-2
Input signals V
L
and T
K
for benchmark adjustment
(Pins No. 11 and 12)
The benchmark level is normally set at the lowest
value of the sensor’s signal (Vg), which is considered
as 400ppm of CO
2
(ambient levels). The benchmark
level Vg is renewed whenever a lower signal voltage
than the present benchmark level is read from the
sensor (as described in
Sec. 1-Automatic calibration
).
If the benchmark level Vg is not renewed for a pre-
set period of time (T
K
), it is automatically adjusted
upward by a pre-set voltage (V
L
) which corresponds
to an equivalent concentration of CO
2
. Table 3 shows
the user-determined settings for V
L
and T
K
which
can be selected by applying a signal to Ports R50 and
R51 respectively.
g
n
S
t
p
n
I
l
n
g
"
H
"
"
L
"
p
u
m
)
T
r
(
w
e
l
i
m
s
n
m
0
3
s
n
m
0
2
1
Table 2 - Initial warm-up time setting (AM-4-4161 default = "L")
g
n
S
l
n
m
r
T
t
p
n
n
g
l
b
m
y
S
.
N
n
"
H
"
"
L
"
k
m
e
e
V
L
)
h
c
n
e
B
l
v
m
(
t
a
0
5
R
1
1
m
p
e
p
5
v
q
t
e
m
p
e
p
0
2
v
q
t
e
k
m
i
e
T
(
K
)
h
c
m
n
e
B
e
m
t
a
1
5
R
2
1
y
a
d
1
s
a
d
7
Table 3 - Benchmark adjustment level and timer setting
(AM-4-4161 default = 20ppm equiv. and 1 day)
相關PDF資料 |
PDF描述 |
|---|---|
| FID-550 | Resistive Touch Panel Specification |
| FID3Z1KX | 320 x 240 pixel format, LED or CFL Backlight |
| FID3Z1LX | 320 x 240 pixel format, LED or CFL Backlight |
| FID3Z2KX | 122 x 32 pixel format, Compact LCD size |
| FID3Z2LX | 122 x 32 pixel format, Compact LCD size |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FIC04G-60 | 制造商:AXIOMTEK 制造商全稱:AXIOMTEK 功能描述:Anti-vibration & shock resistance |
| FIC08G-60 | 制造商:AXIOMTEK 制造商全稱:AXIOMTEK 功能描述:Anti-vibration & shock resistance |
| FIC128-60 | 制造商:AXIOMTEK 制造商全稱:AXIOMTEK 功能描述:Anti-vibration & shock resistance |
| FIC16G-60 | 制造商:AXIOMTEK 制造商全稱:AXIOMTEK 功能描述:Anti-vibration & shock resistance |
| FIC-200 | 功能描述:安全/ 驗證開發工具 PC Card Type II Fingerprint Reader RoHS:否 制造商:Digi International 產品:Development Kits 工具用于評估:XEB-AW140 接口類型:SPI, USB 工作電源電壓:3.1 V to 3.6 V |
發布緊急采購，3分鐘左右您將得到回復。