- 您現在的位置：買賣IC網 > PDF目錄370147 > FAN8005D2 Servo Motor Controller/Driver PDF資料下載
參數資料
| 型號： | FAN8005D2 |
| 英文描述： | Servo Motor Controller/Driver |
| 中文描述： | 伺服電機控制器/驅動器 |
| 文件頁數： | 78/191頁 |
| 文件大?。?/td> | 2018K |
| 代理商： | FAN8005D2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁當前第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁
FAN5201
8
P
Voltage Control Loop
The internal transconductance voltage amplifier controls the
FAN5201’s output voltage. The battery voltage is fed to the
non-inverting input of the amplifier from the VFB pin. The
voltage at the amplifier’s inverting input is set by an 8-bit DAC,
which is controlled by a ChargingVoltage( ) command on the
SMBus (See the FAN5201 Logic section and SMBus Inter-
face Specification for more information). The output of the
amplifier drives an inverting “or’ring” transistor; the or’ring
provides control of the PWM to the lowest of the three ampli-
fiers, while the inversion provides the negative feedback
needed for proper control. The ChargingVoltage( ) command
of the SMBus provides a 10.000V offset, and 32mV steps, so
that the charging voltage can be anywhere from 10.000V to
10.000V + 255 * 32mV = 18.16V. Because a lithium-ion
(Li+) battery’s typical per-cell voltage is 4.2V maximum, this
charger is best suited for 3- and 4-cell batteries. It can also be
used for several different cell counts with NiMH batteries.
The voltage amplifier’s output is connected to the CompV pin,
which compensates the voltage-regulation loop. Typically, a
series-resistor/capacitor combination is used to form a pole-
zero pair. The pole introduced rolls off the gain starting at low
frequencies. The zero provides AC gain at mid-frequencies.
The output capacitor of the switcher then rolls off the mid-
frequency gain to below 1 to guarantee stability, before
encountering the zero introduced by the output capacitor’s
ESR. Further information on loop stabilization is available
in Applications Bulletin AB-18.
Current Control Loop
The internal transconductance current amplifier controls the
battery current while the charger is regulating current. Battery
current is sensed by monitoring the voltage across a sense
resistor (pins IFB and BAT) with an amplifier that removes
the common mode battery voltage. The battery current is fed
to the non-inverting input of the amplifier. The voltage at the
amplifier’s inverting input is set by an 8-bit DAC, which is
controlled by a ChargingCurrent( ) command on the SMBus
(See the FAN5201 Logic section and SMBus Interface Spec-
ification for more information). The output of the amplifier
drives an inverting “or’ring” transistor; the or’ring provides
control of the PWM to the lowest of the three amplifiers,
while the inversion provides the negative feedback needed
for proper control. The ChargingCurrent( ) command of the
SMBus provides 32mA steps with an 18m
sense resistor,
so that the charging current can be anywhere from 0.000A to
255 * 32mA = 8.16A.
The current amplifier’s output is connected to the CompI pin,
which compensates the current-regulation loop. Typically, a
series-resistor/capacitor combination is used to form a pole-
zero pair. The pole introduced rolls off the gain starting at low
frequencies. The zero provides AC gain at mid-frequencies.
The output capacitor of the switcher then rolls off the mid-
frequency gain to below 1 to guarantee stability, before
encountering the zero introduced by the output capacitor’s
ESR. Further information on loop stabilization is available
in Applications Bulletin AB-18.
Power Control Loop
The internal transconductance power amplifier controls the
system’s total power consumption (notebook plus battery
charging). Input voltage is monitored on pin DCIN, and
input current is sensed by monitoring the voltage across a
sense resistor (pins PSIN+ and PSIN-) with an amplifier that
removes the common mode input voltage. These two signals
are then multiplied together with an analog multiplier, and
the result is fed to the non-inverting input of the amplifier.
The voltage at the amplifier’s inverting input is set by a 4-bit
DAC, which is controlled by a ChargingPower( ) command
on the SMBus (See the FAN5201 Logic section and SMBus
Interface Specification for more information). The output of
the amplifier drives an inverting “or’ring” transistor; the
or’ring provides control of the PWM to the lowest of the
three amplifiers, while the inversion provides the negative
feedback needed for proper control. The ChargingPower( )
command of the SMBus provides a 25W offset, and 5W
steps, so that the total power drawn can be anywhere from
25W to 25W + 15 * 5W = 100W.
The power amplifier’s output is connected to the CompP pin,
which compensates the power-regulation loop. Typically, a
series-resistor/capacitor combination is used to form a pole-
zero pair. The pole introduced rolls off the gain starting at low
frequencies. The zero provides AC gain at mid-frequencies.
The output capacitor of the switcher then rolls off the mid-
frequency gain to below 1 to guarantee stability, before
encountering the zero introduced by the output capacitor’s
ESR. Further information on loop stabilization is available
in Applications Bulletin AB-18.
A sudden surge in power required by the notebook will result
in a momentary overload on the AC adapter. This has no ill
effects, because the power loop recovery time is much shorter
than the adapter's thermal time constant, and the minimum
adapter output voltage equals the battery voltage, which is
sufficient to run the notebook.
PWM Controller
The battery voltage or current or input power is controlled by
the pulse-width-modulated (PWM) DC-DC converter control-
ler. This controller drives two external MOSFETs, an N- and
a P-channel, which switch the voltage from the input source.
This switched voltage feeds an inductor, which filters the
switched rectangular wave. The controller sets the pulse width
of the switched voltage so that it supplies the desired voltage
or current to the battery. The heart of the PWM controller is
its multi-input comparator. This comparator compares the
lowest of three input signals with a ramp, to determine the
pulse width of the switched signal, setting the battery voltage
or current. The three signals being or’red together are the
current-sense amplifier’s output, the voltage-error amplifier’s
output, and the power-error amplifier’s output.
相關PDF資料 |
PDF描述 |
|---|---|
| FAN8035L | MOTOR CONTROLLER |
| FAN8039D3 | Servo/Spindle Motor Controller/Driver |
| FAN8800 | |
| FAN6555M | SMPS Controller |
| FAN6555MX | SMPS Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN8005D2TF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Servo Motor Controller/Driver |
| FAN8006D3 | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| FAN8006D3TF | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| FAN8007D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Servo/Spindle Motor Controller/Driver |
| FAN8007DTF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Servo/Spindle Motor Controller/Driver |
發布緊急采購，3分鐘左右您將得到回復。