- 您現在的位置：買賣IC網 > PDF目錄375725 > FAN53180MTC (FAIRCHILD SEMICONDUCTOR CORP) 6-Bit VID Controlled 2-4 Phase DC-DC Controller PDF資料下載
參數資料
| 型號： | FAN53180MTC |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 6-Bit VID Controlled 2-4 Phase DC-DC Controller |
| 中文描述： | SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | TSSOP-28 |
| 文件頁數： | 23/28頁 |
| 文件大小： | 851K |
| 代理商： | FAN53180MTC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁
PRODUCT SPECIFICATION
FAN53180
REV. 1.0.0 6/10/03
23
Note that the capacitor manufacturer’s ripple current ratings
are often based on only 2000 hours of life. This makes it
advisable to further derate the capacitor, or to choose a
capacitor rated at a higher temperature than required. Several
capacitors may be placed in parallel to meet size or height
requirements in the design. In this example, the input capaci-
tor bank is formed by three 2200
μ
F, 16V Nichicon capaci-
tors with a ripple current rating of 3.5 A each.
To reduce the input-current di/dt to below the recommended
maximum of 0.1A/μs, an additional small inductor (L > 1μH
@ 15A) should be inserted between the converter and the
supply bus. That inductor also acts as a filter between the
converter and the primary power source.
TUNING PROCEDURE FOR THE FAN53168
1.
Build circuit based on compensation values computed
from design spreadsheet.
2.
Hook up dc load to circuit, turn on and verify operation.
Also check for jitter at no-load and full-load.
DC Loadline Setting
3.
Measure output voltage at no-load (V
NL
). Verify it is
within tolerance.
Figure 7. Efficiency vs. Output Current (Circuit of Figure 1)
4.
Measure output voltage at full-load cold (V
FLCOLD
).
Let board soak for ~10 minutes at full-load and measure
output (V
FLHOT
). If there is a change of more than a
couple of millivolts, adjust R
CS1
and R
CS2
using
Equations 35 and 37.
5.
Repeat Step 4 until cold and hot voltage measurements
remain the same.
6.
Measure output voltage from no-load to full-load using
5A steps. Compute the loadline slope for each change
and then average to get overall loadline slope (R
OMEAS
).
7.
If R
OMEAS
is off from R
O
by more than 0.05 mW, use
the following to adjust the R
PH
values:
8.
Repeat Steps 6 and 7 to check loadline and repeat
adjustments if necessary.
9.
Once complete with dc loadline adjustment, do not
change R
PH
, R
CS1
, R
CS2
, or R
TH
for rest of procedure.
10. Measure output ripple at no-load and full-load with
scope and make sure it is within spec.
AC Loadline Setting
11. Remove dc load from circuit and hook up dynamic load.
12.
Hook up scope to output voltage and set to dc coupling
with time scale at 100
μ
s/div.
13. Set dynamic load for a transient step of about 40A at
1kHz with 50% duty cycle.
14. Measure output waveform (may have to use dc offset on
scope to see waveform). Try to use vertical scale of 100
mV/div or finer.
15. You will see a waveform that looks something like
Figure 8. Use the horizontal cursors to measure V
ACDRP
and V
DCDRP
as shown. DO NOT MEASURE THE
UNDERSHOOT OR OVERSHOOT THAT HAPPENS
IMMEDIATELY AFTER THE STEP.
I
CRMS
D
I
O
×
n
D
-------------
1
–
×
=
(34)
I
CRMS
0.125
65A
×
------------------------
1
–
×
10.5A
=
=
R
CS2 NEW
)
R
CS2 OLD
)
V
NL
V
FLHOT
–
(
----------------–
)
)
×
=
(35)
100
0
10
20
30
OUTPUT CURRENT – A
E
40
50
60
80
60
40
20
0
R
PH NEW
)
R
PH OLD
)
R
O
----------------------
×
=
(36)
CS2 OLD
CS2 NEW
CS1 OLD
)
TH 25
°
C
(
)
)
)
–
)
R
CS1 OLD
)
R
TH 25
°
C
(
)
–
(
)
×
-----------------------------------------------------------+
TH 25
°
C
(
)
------------------------
–
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
R
CS NEW
(
)
=
(37)
相關PDF資料 |
PDF描述 |
|---|---|
| FAN53180 | 6-Bit VID Controlled 2-4 Phase DC-DC Controller |
| FAN5330 | High Efficiency Serial LED Driver with 30V Integrated Switch |
| FAN5331 | 1.6MHz Boost Converter with 20V Integrated FET Switch |
| FAN5331SX | 1.6MHz Boost Converter with 20V Integrated FET Switch |
| FAN5332A | High Efficiency, High Current Serial LED Driver and OLED Supply with 30V Integrated Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN53180MTCX | 功能描述:DC/DC 開關控制器 Buck Controller 2to4 Phs VID Sync RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| FAN5330 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:High Efficiency Serial LED Driver with 30V Integrated Switch |
| FAN5330SX | 功能描述:LED照明驅動器 SYSTEM_POWER RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| FAN5331 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch |
| FAN5331_05 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch |
發布緊急采購，3分鐘左右您將得到回復。