- 您現在的位置：買賣IC網 > PDF目錄375723 > FAN5019MTC (FAIRCHILD SEMICONDUCTOR CORP) 6-Bit VID Controller 2-4 Phase VRM10.X Controller PDF資料下載
參數資料
| 型號： | FAN5019MTC |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 6-Bit VID Controller 2-4 Phase VRM10.X Controller |
| 中文描述： | SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | TSSOP-28 |
| 文件頁數： | 28/30頁 |
| 文件大小： | 781K |
| 代理商： | FAN5019MTC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁
FAN5019
PRODUCT SPECIFICATION
28
REV. 1.0.7 1/5/04
Whenever a power dissipating component (e.g., a power
MOSFET) is soldered to a PCB, the liberal use of vias,
both directly on the mounting pad and immediately
surrounding it, is recommended. Two important reasons
for this are: improved current rating through the vias, and
improved thermal performance from vias extended to the
opposite side of the PCB where a plane can more readily
transfer the heat to the air. Make a mirror image of any
pad being used to heatsink the MOSFETs on the opposite
side of the PCB to achieve the best thermal dissipation to
the air around the board. To further improve thermal
performance, the largest possible pad area should be used.
The output power path should also be routed to
encompass a short distance. The output power path is
formed by the current path through the inductor, the
output capacitors, and the load.
For best EMI containment, a solid power ground plane
should be used as one of the inner layers extending fully
under all the power components.
Signal Circuitry
The output voltage is sensed and regulated between the
FB pin and the FBRTN pin (which connects to the signal
ground at the load). In order to avoid differential mode
noise pickup in the sensed signal, the loop area should be
small. Thus the FB and FBRTN traces should be routed
adjacent to each other atop the power ground plane back
to the controller.
The feedback traces from the switch nodes should be
connected as close as possible to the inductor. The CSREF
signal should be connected to the output voltage at the
nearest inductor to the controller.
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5019MTCX | 6-Bit VID Controller 2-4 Phase VRM10.X Controller |
| FAN5019 | 6-Bit VID Controller 2-4 Phase VRM10.X Controller |
| FAN5026 | Dual DDR/Dual-output PWM Controller |
| FAN5026MTC | Dual DDR/Dual-output PWM Controller |
| FAN5026MTCX | Dual DDR/Dual-output PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5019MTCX | 功能描述:DC/DC 開關控制器 Sync Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| FAN501MPX | 制造商:Fairchild Semiconductor Corporation 功能描述:PWM CONTROLLER - Tape and Reel |
| FAN5020_AAC3116B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5021_AAC3026B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5026 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Dual DDR/Dual-output PWM Controller |
發布緊急采購，3分鐘左右您將得到回復。