參數資料
型號： EVAL-SSM2380Z
廠商： Analog Devices Inc
文件頁數： 6/32頁
文件大?。?/td> 0K
描述： BOARD EVALUATION FOR SSM2375
標準包裝： 1
放大器類型： D 類
輸出類型： 2 通道（立體聲）
在某負載時最大輸出功率 x 通道數量： 3.2W x 2 @ 4 歐姆
板類型： 完全填充
已用 IC / 零件： SSM2380
已供物品： 板
SSM2380
Rev. A | Page 14 of 32
THEORY OF OPERATION
OVERVIEW
The SSM2380 stereo, Class-D audio amplifier features a filterless
modulation scheme that greatly reduces the external component
count, conserving board space and, thus, reducing system cost.
The SSM2380 does not require an output filter but, instead, relies
on the inherent inductance of the speaker coil and the natural
filtering of the speaker and human ear to fully recover the audio
component of the square wave output.
Most Class-D amplifiers use some variation of pulse-width
modulation (PWM), but the SSM2380 uses Σ-Δ modulation to
determine the switching pattern of the output devices, resulting
in a number of important benefits.
Σ-Δ modulators do not produce a sharp peak with many
harmonics in the AM frequency band, as pulse-width
modulators often do.
Σ-Δ modulation provides the benefits of reducing the
amplitude of spectral components at high frequencies,
that is, reducing EMI emissions that might otherwise
be radiated by speakers and long cable traces.
The SSM2380 does not require external EMI filtering for
twisted speaker cable lengths shorter than 10 cm. If longer
speaker cables are used, the SSM2380 has an emission sup-
pression mode that allows significantly longer speaker cable.
Due to the inherent spread-spectrum nature of Σ-Δ modu-
lation, the need for modulator synchronization is eliminated
for designs that incorporate multiple SSM2380 amplifiers.
Using the I2C control interface, the gain of the SSM2380 can
be selected from 1 dB to 24 dB (plus mute) in 47 steps with no
external components and fixed input impedance. Other features
accessed from the I2C interface include the following:
Independent left/right channel shutdown
Variable ultralow EMI emission control mode
Automatic level control (ALC) for high quality speaker
protection
Stereo-to-mono mixing operation
The SSM2380 also offers protection circuits for overcurrent and
overtemperature protection.
POP-AND-CLICK SUPPRESSION
Voltage transients at the output of audio amplifiers can occur
when shutdown is activated or deactivated. Voltage transients
as low as 10 mV can be heard as an audio pop in the speaker.
Clicks and pops can also be classified as undesirable audible
transients generated by the amplifier system and, therefore, as
not coming from the system input signal. Such transients may
be generated when the amplifier system changes its operating
mode. For example, the following may be sources of audible
transients: system power-up and power-down, mute and
unmute, input source change, and sample rate change.
The SSM2380 has a pop-and-click suppression architecture that
reduces these output transients, resulting in noiseless activation
and deactivation.
OUTPUT MODULATION DESCRIPTION
The SSM2380 uses three-level, Σ-Δ output modulation. Each
output can swing from GND to VDD and vice versa. Ideally, when
no input signal is present, the output differential voltage is 0 V
because there is no need to generate a pulse. In a real-world
situation, noise sources are always present.
Due to the constant presence of noise, a differential pulse is
generated, when required, in response to this stimulus. A small
amount of current flows into the inductive load when the differ-
ential pulse is generated.
Most of the time, however, the output differential voltage is 0 V,
due to the Analog Devices, Inc., three-level, Σ-Δ output modu-
lation. This feature ensures that the current flowing through the
inductive load is small.
When the user wants to send an input signal, an output pulse
(OUTx+ and OUTx) is generated to follow the input voltage.
The differential pulse density (VOUT) is increased by raising the
input signal level. Figure 35 depicts three-level, Σ-Δ output
modulation with and without input stimulus.
OUTPUT > 0V
+5V
0V
OUT+
+5V
0V
OUT–
+5V
0V
VOUT
OUTPUT < 0V
+5V
0V
OUT+
+5V
0V
OUT–
0V
–5V
VOUT
OUTPUT = 0V
OUT+
+5V
0V
+5V
0V
OUT–
+5V
–5V
0V
VOUT
08
75
2-
0
04
Figure 35. Three-Level, Σ-Δ Output Modulation
With and Without Input Stimulus
相關PDF資料
PDF描述
H8MMS-1636M DIP CABLE - HDM16S/AE16M/HDM16S
V24C3V3T50BF2 CONVERTER MOD DC/DC 3.3V 50W
V150B24E150BG2 CONVERTER MOD DC/DC 24V 150W
SSM2306-MINI-EVALZ BOARD EVAL FOR SSM2306-MINI
ECE-A1HKG220 CAP ALUM 22UF 50V 20% RADIAL
相關代理商/技術參數
參數描述
EVAL-SSM2517Z 功能描述:BOARD EVALUATION FOR SSM2517 RoHS:是 類別:編程器，開發系統 >> 評估板 - 音頻放大器 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-
EVAL-SSM2518Z 功能描述:BOARD EVAL FOR SSM2518 RoHS:是 類別:編程器，開發系統 >> 評估板 - 音頻放大器 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:-
EVAL-SSM2519Z 功能描述:音頻 IC 開發工具 SSM2519 EVALUATION BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
EVAL-SSM2529Z 功能描述:音頻 IC 開發工具 SSM2529 EVALUATION BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
EVAL-SSM2537Z 功能描述:音頻 IC 開發工具 SSM2537 EVALUATION BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*