參數資料
型號： EVAL-ADUC834QSZ
廠商： Analog Devices Inc
文件頁數： 53/80頁
文件大?。?/td> 0K
描述： KIT DEV QUICK START ADUC834
標準包裝： 1
系列： QuickStart™ 套件
類型： MCU
適用于相關產品： ADuC834
所含物品： 評估板，線纜，電源，軟件和文檔
REV. A
ADuC834
–57–
UART SERIAL INTERFACE
The serial port is full duplex, meaning it can transmit and
receive simultaneously. It is also receive-buffered, meaning it
can commence reception of a second byte before a previously
received byte has been read from the receive register. However,
if the first byte still has not been read by the time reception of
the second byte is complete, the first byte will be lost. The
physical interface to the serial data network is via Pins
RxD(P3.0) and TxD(P3.1), while the SFR interface to the UART
comprises the following registers:
SBUF
The serial port receive and transmit registers are both accessed
through the SBUF SFR (SFR address = 99H). Writing to SBUF
loads the transmit register and reading SBUF accesses a physically
separate receive register.
SCON
UART Serial Port Control Registers
SFR Address
98H
Power-On Default Value
00H
Bit Addressable
Yes
Table XXX. SCON SFR Bit Designations
Bit
Name
Description
7
SM0
UART Serial Mode Select Bits.
6
SM1
These bits select the Serial Port operating mode as follows:
SM0
SM1
Selected Operating Mode
00
Mode 0: Shift Register, fixed baud rate (fCORE/12)
01
Mode 1: 8-bit UART, variable baud rate
10
Mode 2: 9-bit UART, fixed baud rate (fCORE/64) or (fCORE/32)
11
Mode 3: 9-bit UART, variable baud rate
5
SM2
Multiprocessor Communication Enable Bit.
Enables multiprocessor communication in Modes 2 and 3. In Mode 0, SM2 should be cleared. In
Mode 1, if SM2 is set, RI will not be activated if a valid stop bit was not received. If SM2 is cleared,
RI will be set as soon as the byte of data has been received. In Modes 2 or 3, if SM2 is set, RI will not be
activated if the received ninth data bit in RB8 is 0. If SM2 is cleared, RI will be set as soon as the byte
of data has been received.
4
REN
Serial Port Receive Enable Bit.
Set by user software to enable serial port reception.
Cleared by user software to disable serial port reception.
3TB8
Serial Port Transmit (Bit 9).
The data loaded into TB8 will be the ninth data bit that will be transmitted in Modes 2 and 3.
2
RB8
Serial Port Receiver Bit 9.
The ninth data bit received in Modes 2 and 3 is latched into RB8. For Mode 1, the stop bit is latched into RB8.
1TI
Serial Port Transmit Interrupt Flag.
Set by hardware at the end of the eighth bit in Mode 0, or at the beginning of the stop bit in
Modes 1, 2, and 3.
TI must be cleared by user software.
0RI
Serial Port Receive Interrupt Flag.
Set by hardware at the end of the eighth bit in Mode 0, or halfway through the stop bit in
Modes 1, 2, and 3.
RI must be cleared by software.
UART OPERATING MODES
Mode 0: 8-Bit Shift Register Mode
Mode 0 is selected by clearing both the SM0 and SM1 bits in the
SFR SCON. Serial data enters and exits through RxD. TxD outputs
the shift clock. Eight data bits are transmitted or received. Trans-
mission is initiated by any instruction that writes to SBUF. The
data is shifted out of the RxD line. The 8 bits are transmitted
with the least-significant bit (LSB) first, as shown in Figure 54.
Reception is initiated when the Receive Enable bit (REN) is
1 and the Receive Interrupt bit (RI) is 0. When RI is cleared,
the data is clocked into the RxD line and the clock pulses are
output from the TxD line.
CORE
CLK
ALE
RxD
(DATA OUT)
TxD
(SHIFT CLOCK)
DATA BIT 0
DATA BIT 1
DATA BIT 6
DATA BIT 7
S6
S5
S4
S3
S2
S1
S6
S5
S4
S3
S2
S1
S6
S5
S4
S3
S2
S1
MACHINE
CYCLE 8
MACHINE
CYCLE 7
MACHINE
CYCLE 2
MACHINE
CYCLE 1
Figure 54. UART Serial Port Transmission, Mode 0
相關PDF資料
PDF描述
EVAL-ADUC847QSZ KIT DEV QUICK START FOR ADUC847
GBM24DTKT CONN EDGECARD 48POS DIP .156 SLD
EVAL-ADUC7026QSZ KIT DEV FOR ADUC7026/7027
GEM36DSXS CONN EDGECARD 72POS DIP .156 SLD
GBM18DSAI CONN EDGECARD 36POS R/A .156 SLD
相關代理商/技術參數
參數描述
EVAL-ADUC836QS 制造商:Analog Devices 功能描述:MCU 8BIT 8052 CISC 62KB+4KB FLASH 3.6V 48LQFP - Bulk 制造商:Analog Devices 功能描述:KIT- ADUC836 DEV SYSTEM
EVAL-ADUC841QS 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
EVAL-ADUC841QSP2 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
EVAL-ADUC841QSPZ 功能描述:KIT DEV QUICK START ADUC841 RoHS:是 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ PLUS 套件 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF)
EVAL-ADUC841QSPZ 制造商:Analog Devices 功能描述:Silicon Manufacturer:Analog Devices C
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*