- 您現在的位置：買賣IC網 > PDF目錄16874 > EVAL-ADMP521Z (Analog Devices Inc)BOARD EVAL FOR ADMP521Z PDF資料下載
參數資料
| 型號： | EVAL-ADMP521Z |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 2/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR ADMP521Z |
| 標準包裝： | 1 |
| 系列： | iMEMS® |
| 主要目的： | 音頻，MEMS 全向麥克風 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ADMP521 |
| 主要屬性： | 數字輸出 |
| 已供物品： | 板 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
Data Sheet
ADMP521
Rev. A | Page 9 of 16
CONNECTING PDM MICROPHONES
A PDM output microphone is typically connected to a codec with
a dedicated PDM input. This codec separately decodes the left
and right channels and filters the high sample rate modulated data
back to the audio frequency band. This codec also generates the
clock for the PDM microphones or is synchronous with the source
that is generating the clock. See the Applications Information
section for additional details on connecting the ADMP521 to
Analog Devices, Inc., audio codecs with a PDM input. Figure 11
and Figure 12 show mono and stereo connections of the
ADMP521 and a codec. The mono connection shows an
ADMP521 set to output data on the right channel. To output on
the left channel, tie the L/R SELECT pin to VDD instead of GND.
CLOCK OUTPUT
CODEC
0.1F
1.8V TO 3.3V
GND
L/R SELECT
DATA
ADMP521
CLK
VDD
DATA INPUT
10141-
014
Figure 11. Mono PDM Microphone (Right Channel) Connection to Codec
CLOCK OUTPUT
CODEC
0.1F
1.8V TO 3.3V
GND
L/R SELECT
DATA
ADMP521
CLK
VDD
DATA INPUT
0.1F
1.8V TO 3.3V
GND
L/R SELECT
DATA
ADMP521
CLK
VDD
10141-
015
Figure 12. Stereo PDM Microphone Connection to Codec
capacitor. Place this capacitor as close to VDD as the printed circuit
board (PCB) layout allows.
Do not use a pull-up or pull-down resistor on the PDM data signal
line because it can pull the signal to an incorrect state during the
period that the signal line is tristated.
The DATA signal does not need to be buffered in normal use when
the ADMP521 microphone(s) is placed close to the codec on the
PCB. If the ADMP521 needs to drive the DATA signal over a long
cable (>15 cm) or other large capacitive load, a digital buffer may
be needed. Only use a signal buffer on the DATA line when one
microphone is in use or after the point where two microphones
have been connected (see Figure 13). The DATA output of each
microphone in a stereo configuration cannot be individually
buffered because the two buffer outputs cannot drive a single signal
line. If a buffer is used, take care to select one with low propagation
delay so that the timing of the data connected to the codec is not
corrupted.
When long wires are used to connect the codec to the ADMP521,
a 100 Ω source termination resistor may be used on the clock
output of the codec instead of a buffer to minimize signal over-
shoot or ringing. Depending on the drive capability of the codec
clock output, a buffer may still be needed, as shown in Figure 13.
CLOCK OUTPUT
CODEC
DATA
ADMP521
CLK
DATA INPUT
DATA
CLK
10141-
016
Figure 13. Buffered Connection Between Stereo ADMP521s and a Codec
SLEEP MODE
The microphone enters sleep mode when the clock frequency falls
below 1 kHz. In this mode, the microphone data output is in a
high impedance state. The current consumption in sleep mode
is less than 1 A.
The ADMP521 enters sleep mode within 1 ms of the clock
frequency falling below 1 kHz. The microphone wakes up from
sleep mode in 32,768 cycles after the clock becomes active. With a
3.072 MHz clock, the microphone wake time is 10.7 ms; for a
2.4 MHz clock, the microphone wake time is 13.7 ms.
START-UP
The start-up time of the ADMP521 from when the clock is
active is the same time as the waking from sleep time. The
microphone starts up 32,768 cycles after the clock is active.
OBSOLETE
相關PDF資料 |
PDF描述 |
|---|---|
| PCM18XT0 | MODULE PROC PIC18F4685 |
| MAX6220ASA-5.0+T | IC VREF SERIES PREC 5V 8-SOIC |
| RPP20-4824DW-F | CONV DC/DC 20W 18-75VIN +/-24VOU |
| GCC31DCSH-S288 | CONN EDGECARD 62POS .100 EXTEND |
| XRP2525ID-1-F | IC PWR SW USB 3.0 SINGLE NSOIC8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADMP521Z-FLEX | 功能描述:BOARD EVAL FOR ADMP521Z RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:iMEMS® 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| EVAL-ADMP522Z-FLEX | 制造商:InvenSense Inc 功能描述:ADMP522 - Flexible Evaluation Board, Bulk 制造商:Analog Devices 功能描述:ADMP522 MEMS MICROPHONE EVAL 制造商:Analog Devices 功能描述:ADMP522, MEMS MICROPHONE, EVAL BOARD 制造商:Analog Devices 功能描述:EB Omnidirectional Microphone -PDM 制造商:Analog Devices 功能描述:EVAL BOARD, ADMP522 MEMS MICROPHONE, Silicon Manufacturer:Analog Devices, Silicon Core Number:ADMP522, Kit Application Type:Audio, Video, Application Sub Type:MEMS Microphone, Kit Contents:Eval Board ADMP522 |
| EVAL-ADMP621Z-FLEX | 制造商:AD 制造商全稱:Analog Devices 功能描述:Wide Dynamic Range Microphone with PDM Digital Output |
| EVAL-ADN2525-NTZ | 制造商:Analog Devices 功能描述:OPTICAL EVAL KIT FOR THE ADN2525 - Bulk |
| EVAL-ADN2525-OPZ | 制造商:Analog Devices 功能描述:OPTICAL EVALUATION KIT FOR THE ADN2525 制造商:Analog Devices 功能描述:OPTICAL EVAL KIT FOR THE ADN2525 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。