- 您現在的位置：買賣IC網 > PDF目錄17103 > EVAL-AD5755SDZ (Analog Devices Inc)BOARD EVAL FOR AD5755 PDF資料下載
參數資料
| 型號： | EVAL-AD5755SDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 6/52頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD5755 |
| 視頻文件： | AD5755: 16-Bit Multi-Channel, Voltage and Current Output DAC |
| 標準包裝： | 1 |
| DAC 的數量： | 4 |
| 位數： | 16 |
| 數據接口： | 串行 |
| 設置時間： | 11µs |
| DAC 型： | 電流/電壓 |
| 工作溫度： | -40°C ~ 105°C |
| 已供物品： | 板 |
| 已用 IC / 零件： | AD5755 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
AD5755
Data Sheet
Rev. C | Page 14 of 52
Pin No.
Mnemonic
Description
15
ALERT
Active High Output. This pin is asserted when there has been no SPI activity on the interface pins for a
predetermined time. See the Device Features section for more information.
16
FAULT
Active Low Output. This pin is asserted low when an open circuit in current mode is detected, a short circuit in
voltage mode is detected, a PEC error is detected, or an overtemperature is detected (see the Device Features
section). Open-drain output.
17
POC
Power-On Condition. This pin determines the power-on condition and is read during power-on or, alternatively,
after a device reset. If POC = 0, the device is powered up with the voltage and current channels in tristate mode.
If POC = 1, the device is powered up with a 30 k pull-down resistor to ground on the voltage output channel,
and the current channel is in tristate mode.
18
RESET
Hardware Reset, Active Low Input.
19
AVDD
Positive Analog Supply. The voltage range is from 9 V to 33 V.
20
COMPLV_A
Optional Compensation Capacitor Connection for VOUT_A Output Buffer. Connecting a 220 pF capacitor between
this pin and the VOUT_A pin allows the voltage output to drive up to 2 F. Note that the addition of this capacitor
reduces the bandwidth of the output amplifier, increasing the settling time.
21
VSENSE_A
Sense Connection for the Negative Voltage Output Load Connection for VOUT_A. This pin must stay within ±3.0 V
of AGND for specified operation.
22
+VSENSE_A
Sense Connection for the Positive Voltage Output Load Connection for VOUT_A.
23
COMPDCDC_A
DC-to-DC Compensation Capacitor. Connect a 10 nF capacitor from this pin to ground. Used to regulate the
feedback loop of the Channel A dc-to-dc converter. Alternatively, if using an external compensation resistor,
place a resistor in series with a capacitor to ground from this pin (see the DC-to-DC Converter Compensation
Capacitors and the AICC Supply Requirements—Slewing sections in the Device Features section for more
information).
24
VBOOST_A
Supply for Channel A Current Output Stage (see Figure 72). This is also the supply for the VOUT_x stage, which is
regulated to 15 V by the dc-to-dc converter. To use the dc-to-dc feature of the device, connect as shown in
25
VOUT_A
Buffered Analog Output Voltage for DAC Channel A.
26
IOUT_A
Current Output Pin for DAC Channel A.
27
AVSS
Negative Analog Supply Pin. Voltage range is from 10.8 V to 26.4 V.
28
COMPLV_B
Optional Compensation Capacitor Connection for VOUT_B Output Buffer. Connecting a 220 pF capacitor between
this pin and the VOUT_B pin allows the voltage output to drive up to 2 F. Note that the addition of this capacitor
reduces the bandwidth of the output amplifier, increasing the settling time.
29
VSENSE_B
Sense Connection for the Negative Voltage Output Load Connection for VOUT_B. This pin must stay within ±3.0 V
of AGND for specified operation.
30
+VSENSE_B
Sense Connection for the Positive Voltage Output Load Connection for VOUT_B.
31
VOUT_B
Buffered Analog Output Voltage for DAC Channel B.
32
COMPDCDC_B
DC-to-DC Compensation Capacitor. Connect a 10 nF capacitor from this pin to ground. Used to regulate the
feedback loop of the Channel B dc-to-dc converter. Alternatively, if using an external compensation resistor,
place a resistor in series with a capacitor to ground from this pin (see the DC-to-DC Converter Compensation
Capacitors and the AICC Supply Requirements—Slewing sections in the Device Features section for more
information).
33
IOUT_B
Current Output Pin for DAC Channel B.
34
VBOOST_B
Supply for Channel B Current Output Stage (see Figure 72). This is also the supply for the VOUT_x stage, which is
regulated to 15 V by the dc-to-dc converter. To use the dc-to-dc feature of the device, connect as shown in
35
AGND
Ground Reference Point for Analog Circuitry. This must be connected to 0 V.
36
SWB
Switching Output for Channel B DC-to-DC Circuitry. To use the dc-to-dc feature of the device, connect as shown
37
GNDSWB
Ground Connection for DC-to-DC Switching Circuit. This pin should always be connected to ground.
38
GNDSWA
Ground Connection for DC-to-DC Switching Circuit. This pin should always be connected to ground.
39
SWA
Switching Output for Channel A DC-to-DC Circuitry. To use the dc-to-dc feature of the device, connect as shown
40
AVSS
Negative Analog Supply Pin. The voltage range is from 10.8 V to 26.4 V
41
SWD
Switching Output for Channel D DC-to-DC Circuitry. To use the dc-to-dc feature of the device, connect as shown
42
GNDSWD
Ground Connections for DC-to-DC Switching Circuit. This pin should always be connected to ground.
43
GNDSWC
Ground Connections for DC-to-DC Switching Circuit. This pin should always be connected to ground.
相關PDF資料 |
PDF描述 |
|---|---|
| AT-S-26-6/6/B-14-OE-R | MOD CORD SGL-ENDED 6-6 BLACK 14' |
| VE-J1M-EZ | CONVERTER MOD DC/DC 10V 25W |
| EVAL-AD5755-1SDZ | BOARD EVAL FOR AD5755-1 |
| R-7215D | CONV DC/DC 2A 19-28VIN 15V |
| VE-J14-EZ | CONVERTER MOD DC/DC 48V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD5757SDZ | 功能描述:BOARD EVAL FOR AD5757 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5760SDZ | 功能描述:BOARD EVAL FOR AD5760SDZ RoHS:否 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5764EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD FOR QUAD, 16-BIT, HIGH ACCURACY, SERIAL INPUT, BIPOLAR VOLTAGE OUTPUT DAC 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD I.C. - Bulk |
| EVAL-AD5764EBZ | 功能描述:BOARD EVAL FOR AD5764 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5764REBZ | 功能描述:EVAL BOARD FOR AD5764 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
發布緊急采購，3分鐘左右您將得到回復。