參數資料
型號： EVAL-AD5390EBZ
廠商： Analog Devices Inc
文件頁數： 28/44頁
文件大小： 0K
描述： BOARD EVALUATION FOR AD5390
產品培訓模塊： DAC Architectures
標準包裝： 1
DAC 的數量： 16
位數： 14
采樣率（每秒）： 125k
數據接口： 串行
設置時間： 8µs
DAC 型： 電壓
工作溫度： -40°C ~ 85°C
已供物品： 板，CD
已用 IC / 零件： AD5390
相關產品： AD5390BCPZ-3-REEL7-ND - IC DAC 14BIT 16CH 3V I2C 64LFCSP
AD5390BCPZ-5-ND - IC DAC 14BIT 16CHAN 5V 64LFCSP
AD5390BSTZ-3-ND - IC DAC 14BIT 16CHAN 3V 52LQFP
AD5390BCPZ-5-REEL7-ND - IC DAC 14BIT 16CHAN 5V 64LFCSP
AD5390BCPZ-5-REEL-ND - IC DAC 14BIT 16CHAN 5V 64LFCSP
AD5390BCPZ-3-REEL-ND - IC DAC 14BIT 16CHAN 3V 64LFCSP
AD5390BSTZ-5-ND - IC DAC 14BIT I2C 16CH 52-LQFP
AD5390BCPZ-3-ND - IC DAC 14BIT I2C 16CH 3V 64LFCSP
AD5390/AD5391/AD5392
Data Sheet
Rev. E | Page 34 of 44
Table 27 shows the control register contents of the AD5391. Table 28 provides bit descriptions. Note that REG1 = REG0 = 0,
A3 to A0 = 1100, and DB13 to DB0 contain the control register data.
Table 27. AD5391 Control Register Contents
MSB
LSB
CR11
CR10
CR9
CR8
CR7
CR6
CR5
CR4
CR3
CR2
CR1
CR0
Table 28. AD5391 Bit Descriptions
Bit
Description
CR11
Power-Down Status. This bit is used to configure the output amplifier state in power-down mode.
CR11 = 1: Amplifier output is high impedance (default on power-up).
CR11 = 0: Amplifier output is 100 kΩ to ground.
CR10
REF Select. This bit selects the operating internal reference for the AD5391. CR10 is programmed as follows:
CR10 = 1: Internal reference is 2.5 V (AD5391-5 default). Recommended operating reference for AD5391-5.
CR10 = 0: Internal reference is 1.25 V (AD5391-3 default). Recommended operating reference for AD5391-3.
CR9
Current Boost Control. This bit is used to boost the current in the output amplifier, thus altering its slew rate. This bit is
configured as follows:
CR9 = 1: Boost mode on. This maximizes the bias current in the output amplifier, optimizing its slew rate but increasing
the power dissipation.
CR9 = 0: Boost mode off (default on power-up). This reduces the bias current in the output amplifier and reduces the overall
power consumption.
CR8
Internal/External Reference. This bits determines if the DAC uses its internal reference or an external reference.
CR8 = 1: Internal reference enabled. Reference output depends on data loaded to CR10.
CR8 = 0: External reference selected (default on power-up).
CR7
Channel Monitor Enable (see Table 24).
CR7 = 1: Monitor enabled. This enables the channel monitor function. Following a write to the monitor channel in
the SFR register, the selected channel output is routed to the MON_OUT pin.
CR7 = 0: Monitor disabled (default on power-up). When monitor is disabled, the MON_OUT pin is three-stated.
CR6
Thermal Monitor Function. When enabled, this function is used to monitor the internal die temperature of the AD5391,
when enabled. The thermal monitor powers down the output amplifiers when the temperature exceeds 130°C. This function
can be used to protect the device in cases where the power dissipation of the device may be exceeded, if a number of
output channels are simultaneously short circuited. A soft power-up re-enables the output amplifiers if the die temperature
has dropped below 130°C.
CR6 = 1: Thermal monitor enabled.
CR6 = 0: Thermal monitor disabled (default on power-up).
CR5 to CR2
Don’t Care.
CR1 to CR0
Toggle Function Enable. This function lets the user toggle the output between two codes loaded to the A and B register for
each DAC. Control Register Bit CR1 and Bit CR0 are used to enable individual groups of eight channels for operation in
toggle mode on the AD5391, as follows:
CR1
Group 1
Channel 8 to Channel 15
CR0
Group 0
Channel 0 to Channel 7
Logic 1 written to any bit enables a group of channels and Logic 0 disables a group. LDAC is used to toggle between the two
registers.
相關PDF資料
PDF描述
MIC2026-1YM TR IC SW DISTRIBUTION 2CHAN 8SOIC
EVAL-AD5680EBZ BOARD EVAL FOR AD5680
NRS6010T1R5MMGF INDUCTOR POWER 1.5UH 1.9A SMD
0210490965 CABLE JUMPER 1.25MM .030M 27POS
NR6045T680M INDUCTOR 68UH 900MA 20% SMD
相關代理商/技術參數
參數描述
EVAL-AD5391EB 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk 制造商:Rochester Electronics LLC 功能描述:
EVAL-AD5391EBZ 功能描述:BOARD EVALUATION FOR AD5391 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5392EB 制造商:Analog Devices 功能描述:EVAL BD FOR 8-/16CH, 3V/5 V, SERL INPUT, SGL-SUPPLY,12-/14BI - Bulk
EVAL-AD5392EBZ 功能描述:BOARD EVAL FOR AD5392 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5398AEBZ 制造商:AD 制造商全稱:Analog Devices 功能描述:120 mA, Current Sinking, 10-Bit, I2C DAC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*