參數資料
型號： EPCS64SI16N
廠商： Altera
文件頁數： 13/40頁
文件大?。?/td> 0K
描述： IC CONFIG DEVICE 64MBIT 16-SOIC
產品培訓模塊： Three Reasons to Use FPGA's in Industrial Designs
標準包裝： 49
系列： EPCS
可編程類型： 系統內可編程
存儲容量： 64Mb
電源電壓： 3 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
封裝/外殼： 16-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 16-SOIC
包裝： 管件
產品目錄頁面： 604 (CN2011-ZH PDF)
其它名稱： 544-1380-5
EPCS64SI16
EPCS64SI16N-ND
Page 20
EPCS Device Memory Access
Serial Configuration (EPCS) Devices Datasheet
January 2014
Altera Corporation
Write Status Operation
The write status operation code is b'0000 0001 and it lists the MSB first. Use the write
status operation to set the status register block protection bits. The write status
operation does not affect the other bits. Therefore, you can implement this operation
to protect certain memory sectors, as listed in Table 9 through Table 13. After setting
the block protect bits, the protected memory sectors are treated as read-only memory.
You must execute the write enable operation before the write status operation so the
device sets the status register’s write enable latch bit to 1.
The write status operation is implemented by driving the nCS signal low, followed by
shifting in the write status operation code and one data byte for the status register on
the ASDI pin. Figure 10 shows the instruction sequence of the write status operation.
The nCS must be driven high after the eighth bit of the data byte has been latched in,
otherwise the write status operation is not executed.
Immediately after the nCS signal drives high, the device initiates the self-timed write
status cycle. The self-timed write status cycle usually takes 5 ms for all EPCS devices
and is guaranteed to be less than 15 ms. For more information, refer to the tWS value in
Table 16 on page 29. You must account for this delay to ensure that the status register
is written with desired block protect bits. Alternatively, you can check the write in
progress bit in the status register by executing the read status operation while the
self-timed write status cycle is in progress. The write in progress bit is 1 during the
self-timed write status cycle and 0 when it is complete.
Read Bytes Operation
The read bytes operation code is b'0000 0011 and it lists the MSB first. To read the
memory contents of the EPCS device, the device is first selected by driving the nCS
signal low. Then, the read bytes operation code is shifted in followed by a 3-byte
address (A[23..0]). Each address bit must be latched in on the rising edge of the DCLK
signal. After the address is latched in, the memory contents of the specified address
are shifted out serially on the DATA pin, beginning with the MSB. For reading Raw
Programming Data files (.rpd), the content is shifted out serially beginning with the
LSB. Each data bit is shifted out on the falling edge of the DCLK signal. The maximum
DCLK
frequency during the read bytes operation is 20 MHz.
Figure 10. Write Status Operation Timing Diagram
nCS
DCLK
ASDI
DATA
0
1
2
3
4
5
6
7
8
9
101112131415
Operation Code
Status Register
76543210
MSB
High Impedance
相關PDF資料
PDF描述
XC17S15ASO20C IC PROM SER 5000 C-TEMP 20-SOIC
ICL7663SACBAZA-T IC REG LDO ADJ 40MA 8-SOIC
HMC25DRYN-S734 CONN EDGECARD 50POS DIP .100 SLD
EEC26DRYH-S13 CONN EDGECARD 52POS .100 EXTEND
XC17S15APD8I IC PROM SER 5000 I-TEMP 8-DIP
相關代理商/技術參數
參數描述
EPCSC2.5T 功能描述:接線端子工具和配件 End Plate RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket
EPCSC2.5T1-2 功能描述:接線端子工具和配件 End Plate RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket
EPCSC2.5T2-2 功能描述:接線端子工具和配件 End Plate RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket
EPCSC2.5T2-2/BL 功能描述:接線端子工具和配件 End Plate , Black (50) RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket
EPCSC2.5T2-2/BU 功能描述:接線端子工具和配件 End Plate , Blue (50) RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*