- 您現在的位置：買賣IC網 > PDF目錄19902 > EPC8QC100N (Altera)IC CONFIG DEVICE 8MBIT 100-PQFP PDF資料下載
參數資料
| 型號： | EPC8QC100N |
| 廠商： | Altera |
| 文件頁數： | 9/36頁 |
| 文件大小： | 0K |
| 描述： | IC CONFIG DEVICE 8MBIT 100-PQFP |
| 產品培訓模塊： | Three Reasons to Use FPGA's in Industrial Designs |
| 標準包裝： | 66 |
| 系列： | EPC |
| 可編程類型： | 系統內可編程 |
| 存儲容量： | 8Mb |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 100-BQFP |
| 供應商設備封裝： | 100-PQFP（14x20） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 604 (CN2011-ZH PDF) |
| 其它名稱： | 544-1683 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Functional Description
Page 17
Enhanced Configuration (EPC) Devices Datasheet
January 2012
Altera Corporation
If an external power up monitoring circuit is connected to the RP# pin with the
loop-back connection, use the following guidelines to avoid contention on the RP#
line:
■
The power-up sequence on the 3.3-V supply should complete within 50 ms of
power up. The 3.3-V VCC should reach the minimum VCC before 50 ms and RP#
should then be released.
■ RP#
should be driven low by the power-up monitoring circuit during power up.
After power up, RP# should be tri-stated externally by the power-up monitoring
circuit.
If the preceding guidelines cannot be completed within 50 ms, then the OEpin must be
driven low externally until RP# is ready to be released.
Dynamic Configuration (Page Mode)
The dynamic configuration (or page mode) feature allows the EPC device to store up
to eight different sets of designs for all the FPGAs in your system. You can then
choose which page (set of configuration files) the EPC device should use for FPGA
configuration.
Dynamic configuration or the page mode feature enables you to store a minimum of
two pages—a factory default or fail-safe configuration and an application
configuration. The fail-safe configuration page could be programmed during system
production, while the application configuration page could support remote or local
updates. These remote updates could add or enhance system features and
performance. However, with remote update capabilities comes the risk of possible
corruption of configuration data. In the event of such a corruption, the system could
automatically switch to the fail-safe configuration and avoid system downtime.
The EPC device page mode feature works with the Stratix remote system
configuration feature, to enable intelligent remote updates to your systems.
f For more information about remotely updating Stratix FPGAs, refer to the Remote
System Configuration with Stratix & Stratix GX Devices chapter in the Stratix Device
Handbook.
The three PGM[2..0]input pins control which page is used for configuration and these
pins are sampled at the start of each configuration cycle when OE goes high. The page
mode selection allows you to dynamically reconfigure the functionality of your FPGA
by switching the PGM[2..0] pins and asserting nCONFIG. Page 0 is defined as the
default page and the PGM[2] pin is the MSB.
1 The PGM[2..0] input pins must not be left floating on your board. When you are not
using this feature, connect the PGM[2..0] pins to GND to select the default page 000.
The EPC device pages are dynamically-sized regions in memory. The start address
and length of each page is programmed into the option-bit space of the flash memory
during initial programming. All subsequent configuration cycles sample the PGM[]
pins and use the option-bit information to jump to the start of the corresponding
configuration page. Each page must have configuration files for all FPGAs in your
system that are connected to that EPC device.
相關PDF資料 |
PDF描述 |
|---|---|
| T86E476K020EBAL | CAP TANT 47UF 20V 10% 2917 |
| XC18V01VQG44C | IC PROM REPROGR 1MB 44-VQFP |
| FMM12DRKH | CONN EDGECARD 24POS DIP .156 SLD |
| XC18V01VQ44C | IC PROM SERIAL CONFIG 1M 44-VQFP |
| EMM43DSEN | CONN EDGECARD 86POS .156 EYELET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EPC8QI100 | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 8Mb 50 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPC8QI100N | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 8Mb 50 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPC8XXX | 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC-9 | 制造商:Curtis Industries 功能描述: 制造商:Curtis Industries 功能描述:Conn Barrier Strip 9 POS 9.52mm Solder ST Thru-Hole 15A |
| EPC9001 | 功能描述:BOARD DEV FOR EPC2015 40V GAN RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:eGaN® 標準包裝:1 系列:- 主要目的:數字電位器 嵌入式:- 已用 IC / 零件:AD5258 主要屬性:- 次要屬性:- 已供物品:板 相關產品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
發布緊急采購，3分鐘左右您將得到回復。