- 您現在的位置：買賣IC網 > PDF目錄376982 > DS80C390 Dual CAN High-Speed Microprocessor PDF資料下載
參數資料
| 型號： | DS80C390 |
| 英文描述： | Dual CAN High-Speed Microprocessor |
| 中文描述： | 雙CAN高速微處理器 |
| 文件頁數： | 21/58頁 |
| 文件大小： | 5486K |
| 代理商： | DS80C390 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
DS80C390
21 of 58
110199
During Stop mode the crystal oscillator is halted to maximize power savings. Typically 4 - 10 ms are
required for an external crystal to begin oscillating again once the device receives the exit stimulus. The
ring oscillator, by contrast, is a free-running digital oscillator that has no startup delay. The ring oscillator
feature is enabled by setting the Ring Oscillator Select bit, RGSL (EXIF.1). If enabled, the
microcontroller uses the ring oscillator as the clock source to exit Stop mode, resuming operation in less
than 100 ns. After 65536 oscillations of the external clock source (not the ring oscillator), the device will
clear the Ring Oscillator Mode bit, RGMD (EXIF.2) to indicate that the device has switched from the
ring oscillator to the external clock source.
The ring oscillator runs at approximately 10 MHz, but varies over temperature and voltage. As a result,
no serial communication or precision timing should be attempted while running from the ring oscillator
since the operating frequency is not precise. The default state exits Stop mode without using the ring
oscillator.
TIMED ACCESS PROTECTION
Selected SFR bits are critical to operation, making it desirable to protect them against an accidental write
operation. The Timed Access procedure prevents an errant processor from accidentally altering bits that
would seriously affect processor operation. The Timed Access procedure requires that the write of a
protected bit be immediately preceded by the following two instructions:
MOV 0C7h, #0AAh
MOV 0C7h, #55h
Writing an AAh followed by a 55h to the Timed Access register (location C7h), opens a three-cycle
window that allows software to modify one of the protected bits. If the instruction that seeks to modify
the protected bit is not immediately preceded by these instructions, the write will be ignored. The
protected bits are:
WDCON.6
WDCON.3
WDCON.1
WDCON.0
RCON.0
ACON.2
ACON.1-0
MCON.7-6
MCON.5
MCON.3-0
C0C.3
C1C.3
P4CNT.6
P4CNT.5-0
P5CNT.2-0
COR.7
COR.6-5
COR.4-3
COR.2-1
COR.0
POR
WDIF
EWT
RWT
BGS
SA
AM1-AM0
IDM1-IDM0
CMA
PDCE3-PDCE.0
CRST
CRST
SBCAN
Power-On Reset Flag
Watchdog Interrupt Flag
Watchdog Reset Enable
Reset Watchdog Timer
Band-Gap Select
Stack Address Mode
Address Mode Select bits
Internal Memory Configuration and Location bits
CAN Data Memory Assignment
Program/Data Chip Enables
CAN 0 Reset
CAN 1 Reset
Single Bus CAN
Port 4 Pin Configuration Control Bits
Configuration Control Bits
IRDA Clock Output Enable
CAN 1 Baud Rate Pre-scale Bits
CAN 0 Baud Rate Pre-scale Bits
CAN Clock Output Divide Bit 1 and Bit 0
CAN Clock Output Enable
P5.7-P5.5
IRDACK
C1BPR7-C1BPR6
C0BPR7-C0BPR6
COD1-COD0
CLKOE
相關PDF資料 |
PDF描述 |
|---|---|
| DS80C390-QNR | Dual CAN High-Speed Microprocessor |
| DS80C390-FCR | Dual CAN High-Speed Microprocessor |
| DS80C390-FNR | Dual CAN High-Speed Microprocessor |
| DS80C390-QCR | Dual CAN High-Speed Microprocessor |
| DS80C410 | Network Microcontrollers with Ethernet and CAN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS80C390_00 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Speed Microcontroller User’s Guide Supplement |
| DS80C390_05 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual CAN High-Speed Microprocessor |
| DS80C390+FCR | 制造商:Maxim Integrated Products 功能描述:MICRO DUAL CAN LQFP PB-FREE - Trays |
| DS80C390+QCR | 制造商:Maxim Integrated Products 功能描述:MICRO DUAL CAN PLCC PB-FREE - Rail/Tube |
| DS80C390+QNR | 制造商:Maxim Integrated Products 功能描述:MICRO DUAL CAN PLCC IND PB-FREE - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。