- 您現在的位置：買賣IC網 > PDF目錄1915 > DS31412N (Maxim Integrated Products)IC 12CH DS3/3 FRAMER 349-BGA PDF資料下載
參數資料
| 型號： | DS31412N |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 62/89頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 12CH DS3/3 FRAMER 349-BGA |
| 標準包裝： | 1 |
| 控制器類型： | DS3/E3 調幀器 |
| 接口： | LIU |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 電流 - 電源： | 960mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 349-BGA 裸露焊盤 |
| 供應商設備封裝： | 349-HCBGA（27x27） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁當前第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁
DS3146/DS3146/DS31412 6-/8-/12-Channel DS3/E3 Framers
65 of 89
Register Name:
FSRL
Register Description:
FEAC Status Register Latched
Register Address:
62h
Bit #
7
6
5
4
3
2
1
0
Name
N/A
RFFOL
RFFNL
RFIL
RFCDL
TFIL
Default
—
Note: See Figure 7-8 for details on the interrupt logic for the status bits in the BSRL register.
Bit 0: Transmit FEAC Idle Latched (TFIL). This latched status bit is set to 1 when the TFI status bit in the FSR
register goes high. TFIL is cleared when the host processor writes a 1 to it and is not set again until TFI goes high
again. When TFIL is set, it can cause a hardware interrupt to occur if the TFIIE bit in the FSRIE register and the
FEACIE bit in the MSRIE register are both set. The interrupt is cleared when this bit is cleared or one or both of the
interrupt-enable bits are cleared. This bit can be used to determine when the FEAC codeword transmission has
finished, and thus a new codeword can be transmitted.
Bit 1: Receive FEAC Codeword Detected Latched (RFCDL). This latched status bit is set to 1 when the RFCD
status bit in the FSR register goes high. RFCDL is cleared when the host processor writes a one to it and is not set
again until RFCD goes high again. When RFCDL is set, it can cause a hardware interrupt to occur if the RFCDIE
bit in the FSRIE register and the FEACIE bit in the MSRIE register are both set. The interrupt is cleared when this
bit is cleared or one or both of the interrupt-enable bits are cleared.
Bit 2: Receive FEAC Idle Latched (RFIL). This latched status bit is set to 1 when the RFI status bit in the FSR
register goes high. RFIL is cleared when the host processor writes a 1 to it and is not set again until RFI goes high
again. When RFIL is set, it can cause a hardware interrupt to occur if the RFIIE bit in the FSRIE register and the
FEACIE bit in the MSRIE register are both set. The interrupt is cleared when this bit is cleared or one or both of the
interrupt-enable bits are cleared. This bit can be used to determine when the FEAC receiver has stopped receiving
codewords, which can mark the end of an alarm situation.
Bit 3: Receive FEAC FIFO Not-Empty Latched (RFFNL). This latched status bit is set to 1 when the RFFE bit in
the FSR register goes low. RFFNL is cleared when the host processor writes a 1 to it and is not set again until the
RFFE bit goes low again. When RFFNL is set, it can cause a hardware interrupt to occur if the RFFNIE bit in the
FSRIE register and the FEACIE bit in the MSRIE register are both set. The interrupt is cleared when this bit is
cleared or one or both of the interrupt-enable bits are cleared. This bit can be used to determine when to read
FEAC codeword(s) from the FIFO.
Bit 4: Receive FEAC FIFO Overflow Latched (RFFOL). This latched status bit is set to 1 when the receive FEAC
controller has attempted to write to an already full receive FEAC FIFO and the current incoming FEAC codeword is
lost. RFFOL is cleared when the host processor writes a 1 to it and is not set again until another FIFO overflow
occurs (i.e., the receive FEAC FIFO has been read and then fills beyond capacity). When RFFOL is set, it can
cause a hardware interrupt to occur if the RFFOIE bit in the FSRIE register and the FEACIE bit in the MSRIE
register are both set. The interrupt is cleared when this bit is cleared or one or both of the interrupt-enable bits are
cleared.
相關PDF資料 |
PDF描述 |
|---|---|
| DS3150TN | IC LIU T3/E3/STS-1 IND 48-TQFP |
| DS3154N+ | IC LIU DS3/E3/STS-1 QD 144CSBGA |
| DS3164+ | IC ATM/PACKET PHY QUAD 400-BGA |
| DS3170+ | IC TXRX DS3/E3 100-CSBGA |
| DS3172N+ | IC TXRX DS3/E3 DUAL 400-BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS31415 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3-Input, 4-Output, Single DPLL Timing IC with Sub-ps Output Jitter and 1588 Clock |
| DS31415_1107 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:3-Input, 4-Output, Single DPLL Timing IC with Sub-ps Output Jitter and 1588 Clock |
| DS31415DK | 功能描述:網絡開發工具 DS31415 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
| DS31415GN+ | 制造商:Microsemi Corporation 功能描述:SINGLE DPLL TIMING IC W/APLL & 1588 CLOCK - Rail/Tube 制造商:Zarlink Semiconductor Inc 功能描述:SINGLE DPLL TIMING IC W/APLL & 1588 CLOCK - Rail/Tube 制造商:Microsemi 功能描述:DPLL 256-Pin CSBGA |
| DS3141N | 功能描述:網絡控制器與處理器 IC Single DS3/E3 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。