參數資料
型號： DS3131
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： Telecom IC:Other
英文描述： SPECIALTY TELECOM CIRCUIT, PBGA256
封裝： 27 X 27 MM, PLASTIC, BGA-256
文件頁數： 17/174頁
文件大小： 1261K
代理商： DS3131
DS3131
113 of 174
Figure 9-20. Transmit Done-Queue Structure
Once the transmit DMA is activated (through the TDE control bit in the Master Configuration register;
see Section 5 for more details), it can begin writing data to the done queue. It knows where to write data
into the done queue by reading the write pointer and adding it to the base address to obtain the actual 32-
bit address. Once the DMA writes to the done queue, it increments the write pointer by one dword. A
check must be made to ensure the incremented address does not exceed the transmit done-queue end
address. If the incremented address does exceed this address, then the incremented write pointer is set
equal to 0000h (i.e., the base address).
Status Bits/Interrupts
On writes to the done queue by the DMA, the DMA sets the status bit for the transmit DMA done-queue
write (TDQW) in the status register for DMA (SDMA). The host can configure the DMA to either set
this status bit on each write to the done queue or only after multiple (from 2 to 128) writes. The host
controls this by setting the TDQT0 to TDQT2 bits in the transmit DMA queues-control (TDMAQ)
register. See the description of the TDMAQ register at the end of this section for more details. The DMA
also checks the transmit done-queue host read pointer to ensure that an overflow does not occur. If this
does occur, then the DMA sets the status bit for transmit DMA done-queue write error (TDQWE) in the
status register for DMA (SDMA), and it does not write to the done queue nor does it increment the write
pointer. In such a scenario, information on transmitted packets is lost and unrecoverable. Each of the
status bits can also (if enabled) cause an hardware interrupt to occur. See Section 5 for more details.
Done-Queue Burst Writing
Done-queue FIFO can write descriptors to the done queue, and then it burst writes them, increments the
write pointer, and sets the status bit for transmit DMA done-queue write (TDQW) in the status register
for DMA (SDMA). See Section 5 for more details about status bits.
Base + 00h
Base + 04h
Base + 08h
Base + 0Ch
Base + 10h
Base + 14h
Base + End Address
Pending-Queue Host Write Pointer
Pending-Queue DMA Read Pointer
Maximum of 65,536
Pending-Queue Descriptors
DMA Acquired
Pending-Queue Descriptor
Host Readied
Pending-Queue Descriptor
Host Readied
Pending-Queue Descriptor
Host Readied
Pending-Queue Descriptor
DMA Acquired
Pending-Queue Descriptor
DMA Acquired
Pending-Queue Descriptor
Host Readied
Pending-Queue Descriptor
相關PDF資料
PDF描述
DS3134 DATACOM, FRAMER, PBGA256
DS3150QN DATACOM, PCM TRANSCEIVER, PQCC28
DS3150Q DATACOM, PCM TRANSCEIVER, PQCC28
DS3150TN DATACOM, PCM TRANSCEIVER, PDIP48
DS3150T DATACOM, PCM TRANSCEIVER, PQFP48
相關代理商/技術參數
參數描述
DS3131DK 功能描述:通信集成電路 - 若干 RoHS:否 制造商:Maxim Integrated 類型:Transport Devices 封裝 / 箱體:TECSBGA-256 數據速率:100 Mbps 電源電壓-最大:1.89 V, 3.465 V 電源電壓-最小:1.71 V, 3.135 V 電源電流:50 mA, 225 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube
DS3134 功能描述:IC CTRLR HDLC CHATEAU 256-BGA RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
DS-313PIN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog Miscellaneous
DS-313-PIN 功能描述:信號調節 RoHS:否 制造商:EPCOS 產品:Duplexers 頻率:782 MHz, 751 MHz 頻率范圍: 電壓額定值: 帶寬: 阻抗:50 Ohms 端接類型:SMD/SMT 封裝 / 箱體:2.5 mm x 2 mm 工作溫度范圍:- 30 C to + 85 C 封裝:Reel
DS31400 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:8-Input, 14-Output, Dual DPLL Timing IC with Sub-ps Output Jitter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*