- 您現在的位置：買賣IC網 > PDF目錄385273 > DS26518G (MAXIM INTEGRATED PRODUCTS INC) 8-Port T1/E1/J1 Transceiver PDF資料下載
參數資料
| 型號： | DS26518G |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | 8-Port T1/E1/J1 Transceiver |
| 中文描述： | DATACOM, FRAMER, BGA256 |
| 封裝： | 17 X 17 MM, 1 MM, PITCH, CSBGA-256 |
| 文件頁數： | 56/286頁 |
| 文件大?。?/td> | 1539K |
| 代理商： | DS26518G |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁第235頁第236頁第237頁第238頁第239頁第240頁第241頁第242頁第243頁第244頁第245頁第246頁第247頁第248頁第249頁第250頁第251頁第252頁第253頁第254頁第255頁第256頁第257頁第258頁第259頁第260頁第261頁第262頁第263頁第264頁第265頁第266頁第267頁第268頁第269頁第270頁第271頁第272頁第273頁第274頁第275頁第276頁第277頁第278頁第279頁第280頁第281頁第282頁第283頁第284頁第285頁第286頁
DS26518 8-Port T1/E1/J1 Transceiver
56 of 286
9.9.4.2 Receive-Signaling Operation
There are two methods to access receive-signaling data and provide transmit-signaling data: processor based (i.e.,
software based) or hardware based. Processor-based refers to access through the transmit- and receive-signaling
registers,
RS1
–RS16. Hardware based refers to the RSIGn pin. Both methods can be used simultaneously.
9.9.4.2.1 Processor-Based Receive Signaling
Signaling information is sampled from the receive data stream and copied into the Receive-Signaling Registers,
RS1
–RS16. The signaling information in these registers is always updated on multiframe boundaries. This function
is always enabled.
9.9.4.2.2 Change of State
To avoid constant monitoring of the receive-signaling registers, the DS26518 can be programmed to alert the host
when any specific channel or channels undergo a change of their signaling state.
RSCSE1
–4 are used to select
which channels can cause a change of state indication. The change of state is indicated in Receive Latched Status
Register 4 (
RLS4
.3). If signaling integration is enabled, the new signaling state must be constant for three
multiframes before a change of state indication is indicated. The user can enable the
INTB
pin to toggle low upon
detection of a change in signaling by setting the interrupt mask bit
RIM4
.3. The signaling integration mode is global
and cannot be enabled on a channel-by-channel basis.
The user can identity which channels have undergone a signaling change of state by reading the Receive-
Signaling Status Registers (
RSS1
–4) . The information from these registers will tell the user which RSx register to
read for the new signaling data. All changes are indicated in the RSS1–4 registers regardless of the
RSCSE1
–4
registers.
9.9.4.2.3 Hardware-Based Receive Signaling
In hardware-based signaling the signaling data is can be obtained from the RSERn pin or the RSIGn pin. RSIGn is
a signaling PCM stream output on a channel by channel basis from the signaling buffer. The T1 robbed bit or E1
TS16 signaling data is still present in the original data stream at RSERn. The signaling buffer provides signaling
data to the RSIGn pin and also allows signaling data to be reinserted into the original data stream in a different
alignment that is determined by a multiframe signal from the RSYNCn pin. In this mode, the receive elastic store
may be enabled or disabled. If the receive elastic store is enabled, then the backplane clock (RSYSCLKn) can be
either 1.544MHz or 2.048MHz. In the ESF framing mode, the ABCD signaling bits are output on RSIGn in the lower
nibble of each channel. The RSIGn data is updated once a multiframe (3ms for T1 ESF, 1.5ms for T1 D4, 2ms for
E1 CAS) unless a signaling freeze is in effect. In the D4 framing mode, the AB signaling bits are output twice on
RSIGn in the lower nibble of each channel. Hence, bits 5 and 6 contain the same data as bits 7 and 8, respectively,
in each channel.
9.9.4.2.4 Receive-Signaling Reinsertion at RSERn
In this mode, the user will provide a multiframe sync at the RSYNCn pin and the signaling data will be reinserted
based on this alignment. In T1 mode, this results in two copies of the signaling data in the RSERn data stream. The
original signaling data based on the Fs/ESF frame positions and the realigned data based on the user supplied
multiframe sync applied at RSYNCn. In voice channels this extra copy of signaling data is of little consequence.
Reinsertion can be avoided in data channels since this feature is activated on a per-channel basis. For reinsertion,
the elastic store must be enabled and for T1, the backplane clock can be either 1.544MHz or 2.048MHz. E1
signaling information cannot be reinserted into a 1.544MHz backplane.
Signaling reinsertion mode is enabled, on a per-channel basis by setting the receive-signaling reinsertion channel
select bit high in the
RSI1
–4 register. The channels that are to have signaling reinserted are selected by writing to
the
RSI1
–4 registers. In E1 mode, the user will generally select all channels or none for reinsertion.
9.9.4.2.5 Force Receive-Signaling All Ones
In T1 mode, the user can on a per-channel basis force the robbed-bit signaling bit positions to a one. This is done
by using the Receive-Signaling All-Ones Insertion Registers (
T1RSAOI1
–3). The user sets the channel select bit in
the
T1RSAOI1
–3 registers to select the channels that are to have the signaling forced to one.
相關PDF資料 |
PDF描述 |
|---|---|
| DS26518GN | 8-Port T1/E1/J1 Transceiver |
| DS26519 | 16-Port T1/E1/J1 Transceiver |
| DS26519G | 16-Port T1/E1/J1 Transceiver |
| DS26519GN | 16-Port T1/E1/J1 Transceiver |
| DS26522 | Dual T1/E1/J1 Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS26518G+ | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS26518GA2+ | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS26518GN | 功能描述:網絡控制器與處理器 IC 8-Port E1/T1/J1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS26518GN+ | 功能描述:網絡控制器與處理器 IC 8-Port E1/T1/J1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS26518GNA2+ | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。