- 您現在的位置：買賣IC網 > PDF目錄385273 > DS26303L-75 (MAXIM INTEGRATED PRODUCTS INC) 3.3V, E1/T1/J1, Short-Haul, Octal Line Interface Unit PDF資料下載
參數資料
| 型號： | DS26303L-75 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | 3.3V, E1/T1/J1, Short-Haul, Octal Line Interface Unit |
| 中文描述： | DATACOM, PCM TRANSCEIVER, PQFP144 |
| 封裝： | 20 X 20 MM, 1.40 MM HEIGHT, MS-026, LQFP-144 |
| 文件頁數： | 46/97頁 |
| 文件大?。?/td> | 966K |
| 代理商： | DS26303L-75 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁
DS26303: 3.3V, T1/E1/J1, Short-Haul, Octal Line Interface Unit
46 of 97
5.1.4 BERT Registers
Register Name:
Register Description:
Register Address:
Bit #
Name
PMUM
Default
Bit 7: Performance-Monitoring Update Mode (PMUM).
When 0, a performance-monitoring update is initiated by
the LPMU register bit. When 1, a performance-monitoring update is initiated by the receive performance-monitoring
update signal (RPMU). Note: If RPMU or LPMU is 1, changing the state of this bit may cause a performance-
monitoring update to occur.
BCR
BERT Control Register
00h
7
6
5
4
3
2
1
0
LPMU
0
RNPL
0
RPIC
0
MPR
0
APRD
0
TNPL
0
TPIC
0
0
Bit 6: Local Performance-Monitoring Update (LPMU).
This bit causes a performance-monitoring update to be
initiated if the local performance-monitoring update is enabled (PMUM = 0). A 0-to-1 transition causes the
performance-monitoring registers to be updated with the latest data, and the counters reset (0 or 1). For a second
performance-monitoring update to be initiated, this bit must be set to 0, and back to 1. If LPMU goes low before the
PMS bit goes high, an update might not be performed. This bit has no affect when PMUM = 1.
Bit 5: Receive New Pattern Load (RNPL).
A 0-to-1 transition of this bit causes the programmed test pattern
(QRSS, PTS, PLF[4:0], PTF[4:0], and BSP[31:0]) to be loaded in to the receive pattern generator. This bit must be
changed to 0 and back to 1 for another pattern to be loaded. Loading a new pattern forces the receive pattern
generator out of the sync state, which causes a resynchronization to be initiated. Note: QRSS, PTS, PLF[4:0},
PTF[4:0], and BSP[31:0] must not change from the time this bit transitions from 0 to 1 until four RXCK clock cycles
after this bit transitions from 0 to 1.
Bit 4: Receive Pattern Inversion Control (RPIC).
When 0, the receive incoming data stream is not altered. When
1, the receive incoming data stream is inverted.
Bit 3: Manual Pattern Resynchronization (MPR).
A 0-to-1 transition of this bit causes the receive pattern
generator to resynchronize to the incoming pattern. This bit must be changed to 0 and back to 1 for another
resynchronization to be initiated. Note: A manual resynchronization forces the receive pattern generator out of the
sync state.
Bit 2: Automatic Pattern Resynchronization Disable (APRD).
When 0, the receive pattern generator
automatically resynchronizes to the incoming pattern if six or more times during the current 64-bit window the
incoming data stream bit and the receive pattern generator output bit did not match. When 1, the receive pattern
generator does not automatically resynchronize to the incoming pattern. Note: Automatic synchronization is
prevented by not allowing the receive pattern generator to automatically exit the sync state.
Bit 1: Transmit New Pattern Load (TNPL).
A 0-to-1 transition of this bit causes the programmed test pattern
(QRSS, PTS, PLF[4:0], PTF[4:0], and BSP[31:0]) to be loaded in to the transmit pattern generator. This bit must be
changed to zero and back to one for another pattern to be loaded. Note: QRSS, PTS, PLF[4:0}, PTF[4:0], and
BSP[31:0] must not change from the time this bit transitions from 0 to 1 until four TXCK clock cycles after this bit
transitions from 0 to 1.
Bit 0: Transmit Pattern Inversion Control (TPIC).
When 0, the transmit outgoing data stream is not altered.
When 1, the transmit outgoing data stream is inverted.
相關PDF資料 |
PDF描述 |
|---|---|
| DS26303LN-120 | 3.3V, E1/T1/J1, Short-Haul, Octal Line Interface Unit |
| DS26303LN-75 | 3.3V, E1/T1/J1, Short-Haul, Octal Line Interface Unit |
| DS26518 | 8-Port T1/E1/J1 Transceiver |
| DS26518G | 8-Port T1/E1/J1 Transceiver |
| DS26518GN | 8-Port T1/E1/J1 Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS26303L-75+ | 功能描述:電信線路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| DS26303L-75+A3 | 功能描述:電信線路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| DS26303L-75A3 | 功能描述:電信線路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| DS26303LN-120 | 功能描述:電信線路管理 IC RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| DS26303LN-120+ | 功能描述:電信線路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。