- 您現在的位置：買賣IC網 > PDF目錄4589 > DS2413P+ (Maxim Integrated Products)IC SWITCH DL ADDRESS 6-TSOC PDF資料下載
參數資料
| 型號： | DS2413P+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH DL ADDRESS 6-TSOC |
| 產品培訓模塊： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 120 |
| 系列： | * |
| 類型： | * |
| 應用： | * |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 6-LSOJ |
| 供應商設備封裝： | 6-TSOC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1429 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
DS2413: 1-Wire Dual Channel Addressable Switch
13 of 18
1-Wire SIGNALING
The DS2413 requires strict protocols to ensure data integrity. The protocol consists of four types of signaling on
one line: Reset Sequence with Reset Pulse and Presence Pulse, Write-Zero, Write-One, and Read-Data. Except
for the Presence pulse, the bus master initiates all falling edges. The DS2413 can communicate at two different
speeds, standard speed, and Overdrive Speed. If not explicitly set into the Overdrive mode, the DS2413
communicates at standard speed. While in Overdrive Mode the fast timing applies to all waveforms.
To get from idle to active, the voltage on the 1-Wire line needs to fall from VPUP below the threshold VTL. To get
from active to idle, the voltage needs to rise from VILMAX past the threshold VTH. The time it takes for the voltage to
make this rise is seen in Figure 11 as '
' and its duration depends on the pullup resistor (RPUP) used and the
capacitance of the 1-Wire network attached. The voltage VILMAX is relevant for the DS2413 when determining a
logical level, not triggering any events.
Figure 11 shows the initialization sequence required to begin any communication with the DS2413. A Reset Pulse
followed by a Presence Pulse indicates the DS2413 is ready to receive data, given the correct ROM and PIO
Function command. If the bus master uses slew-rate control on the falling edge, it must pull down the line for tRSTL
+ tF to compensate for the edge. A tRSTL duration of 480s or longer exits the Overdrive Mode, returning the device
to standard speed. If the DS2413 is in Overdrive Mode and tRSTL is no longer than 80s, the device remains in
Overdrive Mode. If the device is in Overdrive Mode and tRSTL is between 80s and 480s, the device will reset, but
the communication speed is undetermined.
Figure 11. Initialization Procedure: Reset and Presence Pulse
RESISTOR
MASTER
DS2413
tRSTL
tPDL
tRSTH
tPDH
MASTER TX “RESET PULSE” MASTER RX “PRESENCE PULSE”
VPUP
VIHMASTER
VTH
VTL
VILMAX
0V
tF
tREC
tMSP
After the bus master has released the line it goes into receive mode. Now the 1-Wire bus is pulled to VPUP through
the pullup resistor, or in case of a DS2482-x00 or DS2480B driver, by active circuitry. When the threshold VTH is
crossed, the DS2413 waits for tPDH and then transmits a Presence Pulse by pulling the line low for tPDL. To detect a
presence pulse, the master must test the logical state of the 1-Wire line at tMSP.
The tRSTH window must be at least the sum of tPDHMAX, tPDLMAX, and tRECMIN. Immediately after tRSTH is expired, the
DS2413 is ready for data communication. In a mixed population network, tRSTH should be extended to minimum
480s at standard speed and 48s at Overdrive speed to accommodate other 1-Wire devices.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2401Z+ | IC SILICON SERIAL NUMBER SOT-223 |
| DS2401P+ | IC SILICON SERIAL NUMBER 6-TSOC |
| LFEC10E-3FN256C | IC FPGA 10.2KLUTS 195I/O 256-BGA |
| LFXP6E-3Q208I | IC FPGA 5.8KLUTS 142I/O 208-PQFP |
| LFXP6C-4Q208C | IC FPGA 5.8KLUTS 142I/O 208-PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2413P/T&R | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2413P+ | 功能描述:接口 - 專用 Dual Addressable Switch RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2413P+ | 制造商:Maxim Integrated Products 功能描述:IC, DUAL CHANNEL ADDRESSABLE SW, TSOC-6 |
| DS2413P+T&R | 制造商:Maxim Integrated Products 功能描述:ADDRESSABLE SWIT 6PIN TSOC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC SWITCH DL ADDRESS 6TSOC 制造商:Maxim Integrated Products 功能描述:Interface - Specialized Dual Addressable Switch |
| DS2413P+T&R | 功能描述:接口 - 專用 Dual Addressable Switch RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。