- 您現在的位置：買賣IC網 > PDF目錄4589 > DS2413P+ (Maxim Integrated Products)IC SWITCH DL ADDRESS 6-TSOC PDF資料下載
參數資料
| 型號： | DS2413P+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 17/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH DL ADDRESS 6-TSOC |
| 產品培訓模塊： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 120 |
| 系列： | * |
| 類型： | * |
| 應用： | * |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 6-LSOJ |
| 供應商設備封裝： | 6-TSOC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1429 (CN2011-ZH PDF) |
DS2413: 1-Wire Dual Channel Addressable Switch
8 of 18
PIO ACCESS WRITE [5Ah]
The PIO Access Write command writes to the PIO output latches, which control the pulldown transistors of the PIO
channels. In an endless loop this command first writes new data to the PIO and then reads back the PIO status.
This implicit read-after-write can be used by the master for status verification. A PIO Access Write can be
terminated at any time with a 1-Wire Reset.
PIO Output Data Bit Assignment
b7
b6
b5
b4
b3
b2
b1
b0
X
PIOB
PIOA
After the command code the master transmits a PIO Output Data byte that determines the new state of the PIO
output transistors. The first (least significant) bit is associated to PIOA; the next bit affects PIOB. The other 6 bits of
the new state byte do not have corresponding PIO pins. These bits should always be transmitted as "1"s. To switch
the output transistor on, the corresponding bit value is 0. To switch the output transistor off (non-conducting) the bit
must be 1. This way the bit transmitted as the new PIO output state arrives in its true form at the PIO pin. To
protect the transmission against data errors, the master must repeat the PIO Output Data byte in its inverted form.
Only if the transmission was error-free will the PIO status change. The actual PIO transition to the new state occurs
with a delay of tREH+x from the rising edge of the MS bit of the inverted PIO byte, as shown in Figure 8. The value
of "x" is approximately 0.2s. To inform the master about the successful communication of the PIO byte, the
DS2413 transmits a confirmation byte with the data pattern AAh. While the MS bit of the confirmation byte is
transmitted, the DS2413 samples the state of the PIO pins, as shown in Figure 7, and sends it to the master. The
master can either continue writing more data to the PIO or issue a 1-Wire Reset to end the command.
Figure 8. PIO Access Write Timing Diagram
IO
PIO
MS 2 bits of inverted
PIO Output Data byte
LS 2 bits of confir-
mation byte (AAh)
VTH
tREH+x
1-Wire BUS SYSTEM
The 1-Wire bus is a system that has a single bus master and one or more slaves. In all instances the DS2413 is a
slave device. The bus master is typically a microcontroller. The discussion of this bus system is broken down into
three topics: hardware configuration, transaction sequence, and 1-Wire signaling (signal types and timing). The
1-Wire protocol defines bus transactions in terms of the bus state during specific time slots, which are initiated on
the falling edge of sync pulses from the bus master.
HARDWARE CONFIGURATION
The 1-Wire bus has only a single line by definition; it is important that each device on the bus be able to drive it at
the appropriate time. To facilitate this, each device attached to the 1-Wire bus must have open-drain or tri-state
outputs. The 1-Wire port of the DS2413 is open drain with an internal circuit equivalent to that shown in Figure 9.
A multidrop bus consists of a 1-Wire bus with multiple slaves attached. The DS2413 supports both a Standard and
Overdrive communication speed of 14.9kbps (max) and 100kbps (max), respectively. Note that legacy 1-Wire
products support a standard communication speed of 16.3kbps and Overdrive of 142kbps. The value of the pullup
resistor primarily depends on the network size and load conditions. The DS2413 requires a pullup resistor of 2.2k
(max) at any speed.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2401Z+ | IC SILICON SERIAL NUMBER SOT-223 |
| DS2401P+ | IC SILICON SERIAL NUMBER 6-TSOC |
| LFEC10E-3FN256C | IC FPGA 10.2KLUTS 195I/O 256-BGA |
| LFXP6E-3Q208I | IC FPGA 5.8KLUTS 142I/O 208-PQFP |
| LFXP6C-4Q208C | IC FPGA 5.8KLUTS 142I/O 208-PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2413P/T&R | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2413P+ | 功能描述:接口 - 專用 Dual Addressable Switch RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2413P+ | 制造商:Maxim Integrated Products 功能描述:IC, DUAL CHANNEL ADDRESSABLE SW, TSOC-6 |
| DS2413P+T&R | 制造商:Maxim Integrated Products 功能描述:ADDRESSABLE SWIT 6PIN TSOC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC SWITCH DL ADDRESS 6TSOC 制造商:Maxim Integrated Products 功能描述:Interface - Specialized Dual Addressable Switch |
| DS2413P+T&R | 功能描述:接口 - 專用 Dual Addressable Switch RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。