- 您現在的位置：買賣IC網 > PDF目錄97868 > DS2252T-128-16 (MAXIM INTEGRATED PRODUCTS INC) 8-BIT, 16 MHz, MICROCONTROLLER, SMA40 PDF資料下載
參數資料
| 型號： | DS2252T-128-16 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Microcontroller |
| 英文描述： | 8-BIT, 16 MHz, MICROCONTROLLER, SMA40 |
| 封裝： | SIMM-40 |
| 文件頁數： | 12/16頁 |
| 文件大小： | 674K |
| 代理商： | DS2252T-128-16 |
DS2252T
5 of 16
PIN
DESCRIPTION
17
RST - Active high reset input. A logic 1 applied to this pin will activate a reset state.
This pin is pulled down internally, can be left unconnected if not used. An RC power-
on reset circuit is not needed and is NOT recommended.
22
ALE - Address Latch Enable. Used to de-multiplex the multiplexed Expanded
Address/Data bus on Port 0. This pin is normally connected to the clock input on a
’373 type transparent latch.
35, 37
XTAL2, XTAL1. Used to connect an external crystal to the internal oscillator. XTAL1
is the input to an inverting amplifier and XTAL2 is the output.
39
GND - Logic ground.
2
VCC - +5V.
24
PROG
- Invokes the Bootstrap loader on a falling edge. This signal should be
debounced so that only one edge is detected. If connected to ground, the
microcontroller will enter Bootstrap loading on power up. This signal is pulled up
internally.
20
SDI – Self-Destruct Input. A logic 1 applied to this input causes a hardware unlock.
This involves the destruction of Encryption Keys, Vector RAM, and the momentary
removal of power from VCCO. This pin should be grounded if not used.
INSTRUCTION SET
The DS2252T executes an instruction set that is object code-compatible with the industry standard 8051
microcontroller. As a result, software development packages such as assemblers and compilers that have
been written for the 8051 are compatible with the DS2252T. A complete description of the instruction set
and operation are provided in the Secure Microcontroller User’s Guide.
MEMORY ORGANIZATION
Figure 2 illustrates the memory map accessed by the DS2252T. The entire 64k of program and 64k of
data are available to the Byte-wide bus. This preserves the I/O ports for application use. An alternate
configuration allows dynamic Partitioning of a 64k space as shown in Figure 3. Any data area not mapped
into the NV RAM is reached via the Expanded bus on Ports 0 and 2. Off-board program memory is not
available for security reasons. Selecting PES = 1 provides access to the real-time clock as shown in
Figure 4. These selections are made using Special Function Registers. The memory map and its controls
are covered in detail in the Secure Microcontroller User’s Guide.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2252T-64-16 | 8-BIT, MICROCONTROLLER, SMA40 |
| DS2252T-32-16 | 8-BIT, MICROCONTROLLER, SMA40 |
| DS2252T | 8-BIT, MICROCONTROLLER, SMA40 |
| DS1722S | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS229E | LINE TRANSCEIVER, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2252T-128-16# | 功能描述:模塊化系統 - SOM 128K Soft MCU Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| DS2252T32-08 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| DS2252T-32-12 | 功能描述:模塊化系統 - SOM RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| DS2252T-32-16 | 功能描述:模塊化系統 - SOM 32K Soft MCU Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| DS2252T-32-16# | 功能描述:模塊化系統 - SOM 32K Soft MCU Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
發布緊急采購，3分鐘左右您將得到回復。