- 您現在的位置：買賣IC網 > PDF目錄1914 > DS21Q41BT (Maxim Integrated Products)IC FRAMER T1 QUAD 128-TQFP PDF資料下載
參數資料
| 型號： | DS21Q41BT |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 61/61頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FRAMER T1 QUAD 128-TQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 72 |
| 控制器類型： | T1 調幀器 |
| 接口： | 并行/串行 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 電流 - 電源： | 30mA |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-LQFP |
| 供應商設備封裝： | 128-LQFP（14x20） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁
DS21Q41B
9 of 61
Receive Clock [RCLK]. 1.544 MHz primary clock. Used to clock data through the receive side of the
framer.
Receive Channel Clock [RCHCLK]. 192 kHz clock which pulses high during the LSB of each channel.
Synchronous with RCLK when the receive side elastic store is disabled. Synchronous with RSYSCLK
when the receive side elastic store is enabled. Useful for parallel to serial conversion of channel data,
locating robbed-bit signaling bits, and for blocking clocks in DDS applications. See Section 12 for timing
details.
Receive Channel Block [RCHBLK]. A user programmable output that can be forced high or low during
any of the 24 T1 channels. Synchronous with RCLK when the receive side elastic store is disabled.
Synchronous with RSYSCLK when the receive side elastic store is enabled. Useful for blocking clocks to
a serial UART or LAPD controller in applications where not all T1 channels are used such as Fractional
T1, 384k bps service, 768k bps, or ISDN-PRI. Also useful for locating individual channels in drop-and-
insert applications and for per-channel loopback. See Section 12 for timing details.
Receive Serial Data [RSER]. Received NRZ serial data. Updated on rising edges of RCLK when the
receive side elastic store is disabled. Updated on the rising edges of RSYSCLK when the receive side
elastic store is enabled.
Receive Sync [RSYNC]. An extracted pulse, one RCLK wide, is output at this pin which identifies either
frame (RCR2.4=0) or multiframe boundaries (RCR2.4=1). If set to output frame boundaries, then via
RCR2.5, RSYNC can also be set to output double-wide pulses on signaling frames. If the receive side
elastic store is enabled, then this pin can be enabled to be an input at which a frame boundary pulse is
applied. See Section 12 for timing details.
Receive Frame Sync (RFSYNC). An extracted 8 kHz pulse, one RCLK wide, is output at this pin which
identifies frame boundaries. See Section 12 for timing details.
Receive Multiframe Sync [RMSYNC]. Only used when the receive side elastic store is enabled. An
extracted pulse, one RSYSCLK wide, is output at this pin which identifies multiframe boundaries. If the
receive side elastic store is disabled, then this output should be ignored. See Section 12 for timing details.
Receive Bipolar Data Inputs [RPOS and RNEG]. Sampled on falling edge of RCLK. Tie together to
receive NRZ data and disable bipolar violation monitoring circuitry.
Receive System Clock [RSYSCLK]. 1.544 MHz or 2.048 MHz clock. Only used when the elastic store
function is enabled. Should be tied low in applications that do not use the elastic store. Allowing this pin
to float can cause the device to 3-state its outputs.
Receive Loss of Sync/Loss of Transmit Clock [RLOS/LOTC]. A dual function output. If CCR1.6=0,
then this pin will toggle high when the synchronizer is searching for the T1 frame and multiframe. If
CCR1.6=1, then this pin will toggle high if the TCLK pin has not been toggled for 5
s.
Receive Alarm Interrupt [ INT ]. Flags host controller during conditions defined in the Status Registers
of the four framers. User can poll the Interrupt Status Register (ISR) to determine which status register in
which framer is active (if any). Active low, open drain output.
3-State Control [Test]. Set high to 3-state all output and I/O pins (including the parallel control port). Set
low for normal operation. Useful in board-level testing.
相關PDF資料 |
PDF描述 |
|---|---|
| DS21Q42T+ | IC FRAMER ENHANCED T1 4X 128TQFP |
| DS21Q43-ATN | IC FRAMER E1 QUAD 5V 128-TQFP |
| DS21Q44T+ | IC FRAMER ENHANCED E1 4X 128TQFP |
| DS21Q50LN | IC TRANSCEIVER E1 QD IND 100LQFP |
| DS21Q55 | IC TXRX QUAD T1/E1/J1 SCT 256BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS21Q41-BT | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS21Q41BT+ | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21Q41BT+T | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS21Q41BTN | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Quad T1 Framer |
| DS21Q41-BTN | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。