- 您現在的位置：買賣IC網 > PDF目錄97867 > DS2182A (DALLAS SEMICONDUCTOR) DATACOM, FRAMER, PDIP28 PDF資料下載
參數資料
| 型號： | DS2182A |
| 廠商： | DALLAS SEMICONDUCTOR |
| 元件分類： | Digital Transmission Controller |
| 英文描述： | DATACOM, FRAMER, PDIP28 |
| 封裝： | 0.600 INCH, DIP-28 |
| 文件頁數： | 21/25頁 |
| 文件大?。?/td> | 270K |
| 代理商： | DS2182A |
DS2182A
5 of 25
register read or write. The following 4 bits identify the register address. The next 2 bits are reserved and
must be set to 0 for proper operation. The last bit of the address/ command word enables burst mode
when set; the burst mode causes all registers to be consecutively read or written to. Data is read and
written to the DS2182A LSB first.
CHIP SELECT AND CLOCK CONTROL
All data transfers are initiated by driving the CS input low. Input data is latched on the rising edge of
SCLK and must be valid during the previous low period of SCLK to prevent momentary corruption of
register data during writes. Data is output on the falling edge of SCLK and held to the next falling edge.
All data transfers are terminated if the CS input transitions high. Port control logic is disabled and SDO is
tri-stated when CS is high.
DATA I/O
Following the eight SCLK cycles that input an address/command byte to write, a data byte is strobed into
the addressed register on the rising edge of the next eight SCLK cycles. Following an address/command
word to read, contents of the selected register are output on the falling edges of the next eight SCLK
cycles. The SDO pin is tri-stated during device write and can be tied to SDI in applications where the host
processor has a bi-directional I/O pin.
BURST MODE
The burst mode allows all onboard registers to be consecutively written to or read by the host processor.
A burst read is used to poll all registers; RSR1 and RSR2 contents will be unaffected. This feature
minimizes device initialization time on system power-up or reset. Burst mode is initiated when ACB.7 is
set and the address is 0000. A burst is terminated by a low-high transition on CS .
ACB: ADDRESS COMMAND BYTE Figure 2
MSB
LSB
BM
-
ADD3
ADD2
ADD1
ADD0
R/ W
SYMBOL
POSITION
NAME AND DESCRIPTION
BM
ACB.7
Burst Mode. If set (and register address is 0000) burst read or
write is enabled.
-
ACB.6
Reserved, must be 0 for operation.
-
ACB.5
Reserved, must be 0 for operation.
ADD3
ACB.4
MSB of register address.
ADD0
ACB.1
LSB of register address.
R/W
ACB.0
Read/Write Select.
0 = write addressed register
1 = read addressed register
相關PDF資料 |
PDF描述 |
|---|---|
| DS2186S | DATACOM, DIGITAL SLIC, PDSO20 |
| DS2187 | DATACOM, PCM TRANSCEIVER, PDIP18 |
| DS2196LN | DATACOM, FRAMER, PQFP100 |
| DS21FF44 | DATACOM, FRAMER, PBGA300 |
| DS21FF44N | DATACOM, FRAMER, PBGA300 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2182AQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM， Other/Special/Miscellaneous |
| DS2182N | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2182Q | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2182Q/T&R | 制造商:Maxim Integrated Products 功能描述:T1 LINE MONITOR-PLCC-TRL - Tape and Reel |
| DS2182Q/T&R | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。