- 您現在的位置：買賣IC網 > PDF目錄97866 > DS2151QB (MAXIM INTEGRATED PRODUCTS INC) DATACOM, FRAMER, PQCC44 PDF資料下載
參數資料
| 型號： | DS2151QB |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Digital Transmission Controller |
| 英文描述： | DATACOM, FRAMER, PQCC44 |
| 封裝： | 0.652 INCH, PLASTIC, LCC-44 |
| 文件頁數： | 10/62頁 |
| 文件大?。?/td> | 921K |
| 代理商： | DS2151QB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
DS2151Q
18 of 60
4.5
Loop Code Generation
When either the CCR3.1 or CCR3.2 bits are set to 1, the DS2151Q will replace the normal transmitted
payload with either the Loop Up or Loop Down code, respectively. The DS2151Q will overwrite the
repeating loop code pattern with the framing bits. The SCT will continue to transmit the loop codes as
long as either bit is set. It is an illegal state to have both CCR3.1 and CCR3.2 set to 1 at the same time.
4.6
Pulse Density Enforcer
The SCT always examines both the transmit and receive data streams for violations of the following rules
which are required by ANSI T1.403-199X:
– no more than 15 consecutive 0s
– at least N 1s in each and every time window of 8 x (N +1) bits where N = 1 through 23
Violations for the transmit and receive data streams are reported in the RIR2.0 and RIR2.1 bits
respectively.
When the CCR3.3 is set to 1, the DS2151Q will force the transmitted stream to meet this requirement no
matter the content of the transmitted stream. When running B8ZS, the CCR3.3 bit should be set to 0,
since B8ZS encoded data streams cannot violate the pulse density requirements.
4.7
Power-Up Sequence
On power-up, after the supplies are stable, the DS2151Q should be configured for operation by writing to
all of the internal registers (this includes setting the Test Register to 00Hex) since the contents of the
internal registers cannot be predicted on power-up. Next, the LIRST bit should be toggled from 0 to 1 to
reset the line interface (it will take the DS2151Q about 40ms to recover from the LIRST being toggled).
Finally, after the SYSCLK input is stable, the ESR bit should be toggled from a 0 to a 1 (this step can be
skipped if the elastic stores are disabled).
相關PDF資料 |
PDF描述 |
|---|---|
| DS2152LN | DATACOM, FRAMER, PQFP100 |
| DS2152L | DATACOM, FRAMER, PQFP100 |
| DS2153Q | DATACOM, FRAMER, PQCC44 |
| DS2154L | DATACOM, FRAMER, PQFP100 |
| DS21554L | DATACOM, PCM TRANSCEIVER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2151QB/T&R | 制造商:Maxim Integrated Products 功能描述:T1 SINGLE CHIP XCVR REV B T&R - Tape and Reel |
| DS2151QB/T&R+ | 制造商:Maxim Integrated Products 功能描述:FRAMER DS1/E1/ISDN-PRI/T1 5V 44PLCC - Tape and Reel |
| DS2151QB/T&R | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2151QB+ | 功能描述:網絡控制器與處理器 IC T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2151QB+T&R | 制造商:Maxim Integrated Products 功能描述:FRAMER DS1/E1/ISDN-PRI/T1 5V 44PLCC - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。