參數資料
型號： DS21354L
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： Digital Transmission Interface
英文描述： DATACOM, PCM TRANSCEIVER, PQFP100
封裝： 14 X 14 MM, LQFP-100
文件頁數： 97/126頁
文件大?。?/td> 1082K
代理商： DS21354L
DS21354/DS21554 3.3V/5V E1 Single-Chip Transceivers
72 of 124
14.3.
Basic Operation Details
As a basic guideline for interpreting and sending HDLC messages, the following sequences can be
applied:
14.3.1.
Example: Receive an HDLC Message
1. Enable RPS interrupts
2. Wait for interrupt to occur
3. Disable RPS interrupt and enable either RPE, RNE, or RHALF interrupt
4. Read RHIR to obtain REMPTY status
a. If REMPTY=0, then record OBYTE, CBYTE, and POK bits and then read the FIFO
a1. if CBYTE = 0 then skip to step 5
a2. if CBYTE = 1 then skip to step 7
b. If REMPTY = 1, then skip to step 6
5. Repeat step 4
6. Wait for interrupt, skip to step 4
7. If POK = 0, then discard whole packet, if POK = 1, accept the packet
a. Disable RPE, RNE, or RHALF interrupt, enable RPS interrupt and return to step 1.
14.3.2.
Example: Transmit an HDLC Message
1. Make sure HDLC controller is done sending any previous messages and is current sending flags by
checking that the FIFO is empty by reading the TEMPTY status bit in the THIR register
2. Enable either the THALF or TNF interrupt
3. Read THIR to obtain TFULL status
a. If TFULL = 0, then write a byte into the FIFO and skip to next step (special case occurs when
the last byte is to be written, in this case set TEOM = 1 before writing the byte and then skip
to step 6)
b. If TFULL = 1, then skip to step 5
4. Repeat step 3
5. Wait for interrupt, skip to step 3
6. Disable THALF or TNF interrupt and enable TMEND interrupt
7. Wait for an interrupt, then read TUDR status bit to make sure packet was transmitted correctly.
相關PDF資料
PDF描述
DS21354LN DATACOM, PCM TRANSCEIVER, PQFP100
DS21372TN SPECIALTY TELECOM CIRCUIT, PQFP32
DS21372T SPECIALTY TELECOM CIRCUIT, PQFP32
DS21372 SPECIALTY TELECOM CIRCUIT, PQFP32
DS2141AN DATACOM, FRAMER, PDIP40
相關代理商/技術參數
參數描述
DS21354L+ 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Single Chip Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21354LB 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Single Chip Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21354LB+ 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Single Chip Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21354LC1 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Single Chip Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21354LC1+ 功能描述:網絡控制器與處理器 IC 3.3/5V E1 Single Chip Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*