參數資料
型號： DS18B20Z
廠商： DALLAS SEMICONDUCTOR
元件分類： Switch/Digital Output Temperature Sensor
英文描述： DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT
封裝： 0.150 INCH, SOIC-8
文件頁數： 2/20頁
文件大?。?/td> 149K
代理商： DS18B20Z
DS18B20
10 of 20
SKIP ROM [CCh]
The master can use this command to address all devices on the bus simultaneously without sending out
any ROM code information. For example, the master can make all DS18B20s on the bus perform
simultaneous temperature conversions by issuing a Skip ROM command followed by a Convert T [44h]
command. Note, however, that the Skip ROM command can only be followed by the Read Scratchpad
[BEh] command when there is one slave on the bus. This sequence saves time by allowing the master to
read from the device without sending its 64–bit ROM code. This sequence will cause a data collision on
the bus if there is more than one slave since multiple devices will attempt to transmit data simultaneously.
ALARM SEARCH [ECh]
The operation of this command is identical to the operation of the Search ROM command except that
only slaves with a set alarm flag will respond.
This command allows the master device to determine if
any DS18B20s experienced an alarm condition during the most recent temperature conversion. After
every Alarm Search cycle (i.e., Alarm Search command followed by data exchange), the bus master must
return to Step 1 (Initialization) in the transaction sequence.
Refer to the OPERATION – ALARM
SIGNALING section for an explanation of alarm flag operation.
DS18B20 FUNCTION COMMANDS
After the bus master has used a ROM command to address the DS18B20 with which it wishes to
communicate, the master can issue one of the DS18B20 function commands. These commands allow the
master to write to and read from the DS18B20’s scratchpad memory, initiate temperature conversions and
determine the power supply mode. The DS18B20 function commands, which are described below, are
summarized in Table 4 and illustrated by the flowchart in Figure 12.
CONVERT T [44h]
This command initiates a single temperature conversion. Following the conversion, the resulting thermal
data is stored in the 2-byte temperature register in the scratchpad memory and the DS18B20 returns to its
low-power idle state. If the device is being used in parasite power mode, within 10
s (max) after this
command is issued the master must enable a strong pullup on the 1-wire bus for the duration of the
conversion (tconv) as described in the POWERING THE DS18B20 section. If the DS18B20 is powered
by an external supply, the master can issue read time slots after the Convert T command and the
DS18B20 will respond by transmitting 0 while the temperature conversion is in progress and 1 when the
conversion is done. In parasite power mode this notification technique cannot be used since the bus is
pulled high by the strong pullup during the conversion.
WRITE SCRATCHPAD [4Eh]
This command allows the master to write 3 bytes of data to the DS18B20’s scratchpad. The first data
byte is written into the TH register (byte 2 of the scratchpad), the second byte is written into the TL
register (byte 3), and the third byte is written into the configuration register (byte 4). Data must be
transmitted least significant bit first. All three bytes MUST be written before the master issues a reset, or
the data may be corrupted.
READ SCRATCHPAD [BEh]
This command allows the master to read the contents of the scratchpad. The data transfer starts with the
least significant bit of byte 0 and continues through the scratchpad until the 9
th byte (byte 8 – CRC) is
read. The master may issue a reset to terminate reading at any time if only part of the scratchpad data is
needed.
COPY SCRATCHPAD [48h]
This command copies the contents of the scratchpad TH, TL and configuration registers (bytes 2, 3 and 4)
to EEPROM. If the device is being used in parasite power mode, within 10
s (max) after this command
相關PDF資料
PDF描述
DS18B20 DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, THROUGH HOLE MOUNT
DS18B20U+T&R DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, SQUARE, SURFACE MOUNT
DS18B20-SL+T&R DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, THROUGH HOLE MOUNT
DS18B20/T&R DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, THROUGH HOLE MOUNT
DS18B20U DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, SQUARE, SURFACE MOUNT
相關代理商/技術參數
參數描述
DS18B20Z/T&R 制造商:Maxim Integrated Products 功能描述:HI RES MICROLAN DIG THERM 8-SOIC TR - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERM MICROLAN PROG-RES 8SOIC 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Prgmble Resolution 1-Wire Parasite Pwr
DS18B20Z/T&R 功能描述:板上安裝溫度傳感器 Prgmble Resolution 1-Wire Parasite Pwr RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS18B20Z+ 功能描述:板上安裝溫度傳感器 Prgmble Resolution 1-Wire Parasite Pwr RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS18B20Z+ 制造商:Maxim Integrated Products 功能描述:SEMICONDUCTOR ((NW))
DS18B20Z+T&R 制造商:Maxim Integrated Products 功能描述:HI RES MICROLAN DIG THERM 8-SOIC TR 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL SERL (1-WIRE) 8SOIC N - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERM MICROLAN PROG-RES 8SOIC 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Prgmble Resolution 1-Wire Parasite Pwr
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*