- 您現在的位置：買賣IC網 > PDF目錄97865 > DS1822-PAR+T&R (MAXIM INTEGRATED PRODUCTS INC) DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT PDF資料下載
參數資料
| 型號： | DS1822-PAR+T&R |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| 封裝： | TO-92, 3 PIN |
| 文件頁數： | 16/19頁 |
| 文件大?。?/td> | 206K |
| 代理商： | DS1822-PAR+T&R |
DS1822-PAR
6 of 19
Data is written to bytes 2, 3, and 4 of the scratchpad using the Write Scratchpad [4Eh] command, and the
data must be transmitted to the DS1822-PAR starting with the least significant bit of byte 2. To verify
data integrity, the scratchpad can be read (using the Read Scratchpad [BEh] command) after the data is
written. When reading the scratchpad, data is transferred over the 1-Wire bus starting with the least
significant bit of byte 0. To transfer the TH, TL and configuration data from the scratchpad to EEPROM,
the master must issue the Copy Scratchpad [48h] command.
Data in the EEPROM registers is retained when the device is powered down; at power-up the EEPROM
data is reloaded into the corresponding scratchpad locations. Data can also be reloaded from EEPROM to
the scratchpad at any time using the Recall E
2
[B8h] command. The master can issue “read-time slots”
(see the 1-WIRE BUS SYSTEM section) following the Recall E
2 command and the DS1822-PAR will
indicate the status of the recall by transmitting 0 while the recall is in progress and 1 when the recall is
done.
CONFIGURATION REGISTER
Byte 4 of the scratchpad memory contains the configuration register, which is organized as
illustrated in Figure 7. The user can set the conversion resolution of the DS1822-PAR using the R0 and
R1 bits in this register as shown in Table 3. The power-up default of these bits is R0 = 1 and R1 = 1 (12-
bit resolution). Note that there is a direct tradeoff between resolution and conversion time. Bit 7 and bits
0-4 in the configuration register are reserved for internal use by the device and cannot be overwritten.
CONFIGURATION REGISTER Figure 7
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
0
R1
R0
1
THERMOMETER RESOLUTION CONFIGURATION Table 3
R1
R0
Resolution
Max Conversion Time
0
9-bit
93.75 ms
(tCONV/8)
0
1
10-bit
187.5 ms
(tCONV/4)
1
0
11-bit
375 ms
(tCONV/2)
1
12-bit
750 ms
(tCONV)
CRC GENERATION
CRC bytes are provided as part of the DS1822-PAR’s 64-bit ROM code and in the 9
th byte of the
scratchpad memory. The ROM code CRC is calculated from the first 56 bits of the ROM code and is
contained in the most significant byte of the ROM. The scratchpad CRC is calculated from the data stored
in the scratchpad, and therefore it changes when the data in the scratchpad changes. The CRCs provide
the bus master with a method of data validation when data is read from the DS1822-PAR. To verify that
data has been read correctly, the bus master must recalculate the CRC from the received data and then
compare this value to either the ROM code CRC (for ROM reads) or to the scratchpad CRC (for
scratchpad reads). If the calculated CRC matches the read CRC, the data has been received error free. The
comparison of CRC values and the decision to continue with an operation are determined entirely by the
bus master. There is no circuitry inside the DS1822-PAR that prevents a command sequence from
相關PDF資料 |
PDF描述 |
|---|---|
| DS1822-PAR/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822-PAR | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.20Cel, ROUND, THROUGH HOLE MOUNT |
| DS1822Z/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS1822/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
| DS1822 | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, THROUGH HOLE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS-18-22-RS | 制造商:TE Connectivity 功能描述:Red sealed splice terminal,0.5-1.5sq.mm |
| DS1822-W | 制造商:Maxim Integrated Products 功能描述:1-WIRE DIGITAL THERMOMETER SOIC - Rail/Tube |
| DS1822Z | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1822Z/T | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Econo 1-Wire Digital Thermometer |
| DS1822Z/T&R | 制造商:Maxim Integrated Products 功能描述:1-WIRE DIGITAL THERMOMETER SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER ECONO DIG 8-SOIC |
發布緊急采購，3分鐘左右您將得到回復。