參數資料
型號: DS17487N-3
廠商: Maxim Integrated Products
文件頁數: 16/31頁
文件大小: 0K
描述: IC RTC 3V 4K NV RAM 24-EDIP
標準包裝: 15
類型: 時鐘/日歷
特點: 警報器,夏令時,閏年,NVSRAM,方波輸出
存儲容量: 4KB
時間格式: HH:MM:SS(12/24 小時)
數據格式: YY-MM-DD-dd
接口: 并聯
電源電壓: 2.7 V ~ 3.7 V
電壓 - 電源,電池: 2.5 V ~ 3.7 V
工作溫度: -40°C ~ 85°C
安裝類型: 通孔
封裝/外殼: 24-DIP 模塊(0.600",15.24mm)
供應商設備封裝: 24-EDIP
包裝: 管件
The timing associated with both the wake-up and kick-
starting sequences is illustrated in the
Wake-
Up/Kickstart Timing Diagram (Figure 6). The timing
associated with these functions is divided into five inter-
vals, labeled 1 to 5 on the diagram.
The occurrence of either a kickstart or wake-up condition
causes the PWR pin to be driven low, as described
above. During interval 1, if the supply voltage on the
DS17x85/DS17x87 VCC pin rises above the greater of
VBAT or VPF before the power-on timeout period (tPOTO)
expires, then PWR remains at the active-low level. If VCC
does not rise above the greater of VBAT or VPF in this
time, then the PWR output pin is turned off and returns to
its high-impedance level. In this event, the IRQ pin also
remains tri-stated. The interrupt flag bit (either WF or KF)
associated with the attempted power-on sequence
remains set until cleared by software during a subse-
quent system power-on.
If VCC is applied within the timeout period, then the sys-
tem power-on sequence continue as shown in intervals
2 to 5 in the timing diagram. During interval 2, PWR
remains active and IRQ is driven to its active-low level,
indicating that either WF or KF was set in initiating the
power-on. In the diagram KS is assumed to be pulled
up to the VBAUX supply. Also at this time, the PAB bit is
automatically cleared to 0 in response to a successful
power-on. The PWR line remains active as long as the
PAB remains cleared to 0.
DS17285/DS17287/DS17485/DS17487/DS17885/DS17887
Real-Time Clocks
____________________________________________________________________
23
Figure 6. Wake-Up/Kickstart Timing Diagram
Note: Wake-up/kickstart timeout is generated only when the oscillator is enabled and the countdown chain is not reset.
VBAT
VIH
tKSPW
tPOTP
VIH
1
2
3
45
VIL
HIGH-IMPEDANCE
VIL
VPF
0V
*CONDITION
VPF < VBAT
*THIS CONDITION CAN OCCUR WITH THE 3V DEVICE.
NOTE: THE TIME INTERVALS SHOWN ABOVE ARE REFERENCED IN THE WAKE-UP/KICKSTART SECTION.
*CONDITION
VBAT > VPF
WF/KF
(INTERNAL)
KS
PWR
IRQ
Table 6. Wake-Up/Kickstart Timing
(TA =+25°C)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
Kickstart-Input Pulse Width
tKSPW
2s
Wake-Up/Kickstart Power-On
Timeout
tPOTO
2s
相關PDF資料
PDF描述
MS27472E18B35SA CONN RCPT 66POS WALL MNT W/SCKT
MS27468T21B11PB CONN RCPT 11POS JAM NUT W/PINS
DS17885SN-5 IC RTC 5V 8K NV RAM IND 24-SOIC
MS3106A32-12S CONN PLUG 15POS STRAIGHT W/SCKT
MS3106F32-1P CONN PLUG 5POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
DS17487N-5 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:3V/5V Real-Time Clock
DS17488 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:3V/5V Real-Time Clock
DS1750Y-150 制造商:未知廠家 制造商全稱:未知廠家 功能描述:NVRAM (Battery Based)
DS1750Y-150-IND 制造商:未知廠家 制造商全稱:未知廠家 功能描述:NVRAM (Battery Based)
DS1750Y-200 制造商:未知廠家 制造商全稱:未知廠家 功能描述:NVRAM (Battery Based)