- 您現在的位置：買賣IC網 > Datasheet目錄39 > DS1722S (Maxim Integrated)IC THERMOMETER DIG 3-WIRE 8-SOIC Datasheet資料下載
參數資料
| 型號： | DS1722S |
| 廠商： | Maxim Integrated |
| 文件頁數： | 6/14頁 |
| 文件大?。?/td> | 384K |
| 描述： | IC THERMOMETER DIG 3-WIRE 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 功能： | 溫度計，恒溫計 |
| 傳感器類型： | 內部 |
| 感應溫度： | -55°C ~ 120°C |
| 精確度： | ±3°C（最小值） |
| 拓?fù)洌?/td> | ADC，寄存器庫 |
| 輸出類型： | SPI? |
| 輸出警報： | 無 |
| 輸出風扇： | 無 |
| 電源電壓： | 2.65 V ~ 5.5 V |
| 工作溫度： | -55°C ~ 120°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
DS1722
6 of 14
CONFIGURATION/STATUS REGISTER Figure 2
1
1
1
1SHOT
R2
R1
R0
SD
MSb
LSb
1SHOT = One-shot temperature conversion bit. If the SD bit is "1", (continuous temperature
conversions are not taking place), a "1" written to the 1SHOT bit will cause the DS1722 to perform one
temperature conversion and store the results in the temperature register at addresses 01h (LSB) and 02h
(MSB). The bit will clear itself to "0" upon completion of the temperature conversion. The user has
read/write access to the 1SHOT bit, although writes to this bit will be ignored if the SD bit is a "0",
(continuous conversion mode). The power-up default of the one-shot bit is "0".
R0, R1, R2 = Thermometer resolution bits. Table 5 below defines the resolution of the digital
thermometer, based on the settings of these 3 bits. There is a direct tradeoff between resolution and
conversion time, as depicted in the AC Electrical Characteristics. The user has read/write access to the
R2, R1 and R0 bits and the power-up default state is R2="0", R1="0", and R0="1" (9-bit conversions).
THERMOMETER RESOLUTION CONFIGURATION Table 5
R2 R1 R0
Thermometer Resolution
Max Conversion Time
0
0
0
8-bit
0.075s
0
0
1
9-bit
0.15s
0
1
0
10-bit
0.3s
0
1
1
11-bit
0.6s
1
x
x
12-bit
1.2s
x=Dont care.
SD = Shutdown bit. If SD is "0", the DS1722 will continuously perform temperature conversions and
store the last completed result in the temperature register. If SD is changed to a "1", the conversion in
progress will be completed and stored and then the device will revert to a low-power shutdown mode.
The communication port remains active. The user has read/write access to the SD bit and the power-up
default is "1" (shutdown mode).
SERIAL INTERFACE
The DS1722 offers the flexibility to choose between two serial interface modes. The DS1722 can
communicate with the SPI interface or with a standard 3-wire interface. The interface method used is
determined by the SERMODE pin. When this pin is connected to V
DDD
SPI communication is selected.
When this pin is connected to ground, standard 3-wire communication is selected.
SERIAL PERIPHERAL INTERFACE (SPI)
The serial peripheral interface (SPI) is a synchronous bus for address and data transfer. The SPI mode of
serial communication is selected by tying the SERMODE pin to V
DDD
. Four pins are used for the SPI.
The four pins are the SDO (Serial Data Out), SDI (Serial Data In), CE (Chip Enable), and SCLK (Serial
Clock). The DS1722 is the slave device in an SPI application, with the microcontroller being the master.
The SDI and SDO pins are the serial data input and output pins for the DS1722, respectively. The CE
input is used to initiate and terminate a data transfer. The SCLK pin is used to synchronize data
movement between the master (microcontroller) and the slave (DS1722) devices.
The shift clock (SCLK), which is generated by the microcontroller, is active only when CE is high and
during address and data transfer to any device on the SPI bus. The inactive clock polarity is
programmable in some microcontrollers. The DS1722 offers an important feature in that the level of the
相關PDF資料 |
PDF描述 |
|---|---|
| DS1775R7+T&R | IC THERMOM/STAT DIG 111 SOT-23-5 |
| DS1821C+ | IC THERMOMETER/STAT PROG 3-TO92 |
| DS1825U+T&R | IC THERMOMETER DIGITAL 8-USOP |
| DS1842N+T&R | IC CURRENT MONITOR 14TDFN |
| DS18B20+PAR | IC THERM MICROLAN PROG-RES TO-92 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1722S/T&R | 制造商:Maxim Integrated Products 功能描述:SPI 3-WIRE THERMOMETER SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER DIG 3-WIRE 8-SOIC |
| DS1722S/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1722S+ | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1722S+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 3-WIRE/SPI 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER DIG 3-WIRE 8-SOIC |
| DS1722S+T&R | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。