參數資料
型號: DS1722S
廠商: Maxim Integrated
文件頁數: 3/14頁
文件大?。?/td> 384K
描述: IC THERMOMETER DIG 3-WIRE 8-SOIC
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 100
功能: 溫度計,恒溫計
傳感器類型: 內部
感應溫度: -55°C ~ 120°C
精確度: ±3°C(最小值)
拓?fù)洌?/td> ADC,寄存器庫
輸出類型: SPI?
輸出警報:
輸出風扇:
電源電壓: 2.65 V ~ 5.5 V
工作溫度: -55°C ~ 120°C
安裝類型: 表面貼裝
封裝/外殼: 8-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 8-SOIC
包裝: 管件
DS1722
 
3 of 14
OVERVIEW
A block diagram of the DS1722 is shown in Figure 1. The DS1722 consists of four major components:
 
1. Precision temperature sensor
 
2. Analog-to-digital converter
 
3. SPI/3-wire interface electronics
 
4. Data registers
 
The factory-calibrated temperature sensor requires no external components. The DS1722 is in a power-
conserving shutdown state upon power-up. After power-up, the user may alter the configuration register
to place the device in a continuous temperature conversion mode or in a one-shot conversion mode. In
the continuous conversion mode, the DS1722 continuously converts the temperature and stores the result
in the temperature register. As conversions are performed in the background, reading the temperature
register does not affect the conversion in progress. In the one-shot temperature conversion mode, the
DS1722 will perform one temperature conversion, store the result in the temperature register, and then
return to the shutdown state. This conversion mode is ideal for power sensitive applications. More
information on the configuration register is contained in the OPERATION-Programming section.
 
The temperature conversion results will have a default resolution of 9 bits. In applications where small
incremental temperature changes are critical, the user can change the conversion resolution from 9 bits to
8, 10, 11, or 12. This is accomplished by programming the configuration register. Each additional bit of
resolution approximately doubles the conversion time.
 
The DS1722 can communicate using either a Motorola Serial Peripheral Interface (SPI) or standard 3-
wire interface. The user can select either communication standard through the SERMODE pin, tying it to
V
DDD
 for SPI and to ground for 3-wire.
 
The device contains both an analog supply voltage and a digital supply voltage (V
DDA
  and V
DDD
,
respectively). The analog supply powers the device for operation while the digital supply provides the
top rails for the digital inputs and outputs. The DS1722 was designed to be 1.8V Logic-Ready.
 
相關PDF資料
PDF描述
DS1775R7+T&R IC THERMOM/STAT DIG 111 SOT-23-5
DS1821C+ IC THERMOMETER/STAT PROG 3-TO92
DS1825U+T&R IC THERMOMETER DIGITAL 8-USOP
DS1842N+T&R IC CURRENT MONITOR 14TDFN
DS18B20+PAR IC THERM MICROLAN PROG-RES TO-92
相關代理商/技術參數
參數描述
DS1722S/T&R 制造商:Maxim Integrated Products 功能描述:SPI 3-WIRE THERMOMETER SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER DIG 3-WIRE 8-SOIC
DS1722S/T&R 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS1722S+ 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
DS1722S+T&R 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 3-WIRE/SPI 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER DIG 3-WIRE 8-SOIC
DS1722S+T&R 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor