- 您現在的位置：買賣IC網 > PDF目錄97863 > DS1626U/T&R (MAXIM INTEGRATED PRODUCTS INC) DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | DS1626U/T&R |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | MICRO, SOP-8 |
| 文件頁數： | 2/12頁 |
| 文件大?。?/td> | 141K |
| 代理商： | DS1626U/T&R |
DS1626/DS1726
10 of 12
Table 4. RESOLUTION CONFIGURATION
R1
R0
RESOLUTION
(BITS)
CONVERSION
TIME (MAX)
(ms)
0
9
93.75
0
1
10
187.5
1
0
11
375
1
12
750
3-WIRE SERIAL DATA BUS
The 3-wire bus consists of three signals:
RST (active-low reset), CLK (clock), and DQ (data). 3-wire
communication is controlled by the
RST signal, which functions as “chip select” signal. All data is
transferred LSb first over the 3-wire bus. All communication with the DS1626/DS1726 is initiated by
driving
RST high. Driving RST low terminates communications and causes DQ to go to a high-
impedance state. Note that
RST must be toggled low after every communication sequence to ensure that
subsequent commands are recognized by the DS1626/DS1726.
When writing to the DS1626/DS1726, data must be valid during the rising edge of CLK. During read
operations the DS1626/DS1726 output data on DQ on the falling edge of CLK and the data remains valid
through the following rising edge, at which time the DQ pin becomes high impedance until the next
falling edge.
To communicate with the DS1626/DS1726, the master must first drive
RST high and then begin
generating the CLK signal while transmitting the desired DS1626/DS1726 command byte. If the
command is a Start Convert T, Stop Convert T, or Software POR command, the transaction is finished
when the last bit of the command has been sent. Figure 7a illustrates a Start Convert T command
sequence.
When writing to the DS1626/DS1726, the master must begin transmitting data during the clock cycle
immediately following the command byte. The DS1626/DS1726 will save only the number of data bits
needed for the specific transaction. For example, for the Write TH or Write TL commands, after twelve
bits of data have been transmitted by the master, the DS1626/DS1726 will ignore any subsequent data
transmitted before
RST goes low. Thus, if data is being transmitted in byte-length segments, the
DS1626/DS1726 will load the first twelve bits into the TH/TL register, and the next four bits will be
ignored. On the other hand, it is necessary to transmit at least the required number of bits for the
requested transaction (i.e., 12-bits to TH/TL or 8-bits to the configuration register), because the
DS1626/DS1726 will not save data until the expected number of bits have been received. Write TH and
Write TL sequences are illustrated in Figure 7b and a Write Config sequence is shown in Figure 7c. Note
that these figures assume byte-wide data transfers.
When reading data from the DS1626/DS1726, the DS1626/DS1726 will begin sending data during the
clock cycle immediately following the command byte. After the last data byte has been sent, the
DS1626/DS1726 will transmit a 0 during each subsequent clock until
RST goes low. Figure 7d illustrates
a Read Temperature sequence and a Read Config transaction is shown in Figure 7e. The sequence for
reading the TH or TL registers is the same as the Read Temp transaction in Figure 7d except that the Read
TH or Read TL command is used.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1626U | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| DS1726U+ | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 0.50Cel, RECTANGULAR, SURFACE MOUNT |
| DS17285E-3 | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
| DS17285E-5 | 1 TIMER(S), REAL TIME CLOCK, PDSO28 |
| DS17285S-5 | 1 TIMER(S), REAL TIME CLOCK, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1628 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Octal TRI-STATE MOS Drivers |
| DS1628J | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Octal TRI-STATE MOS Drivers |
| DS1628J/A+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Memory Driver |
| DS1629 | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:2-Wire Digital Thermometer and Real Time Clock |
| DS1629S | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。