- 您現在的位置：買賣IC網 > PDF目錄376954 > DS1620S IC-SM-DIGITAL THERMOMETER PDF資料下載
參數資料
| 型號： | DS1620S |
| 元件分類： | 溫度傳感器 |
| 英文描述： | IC-SM-DIGITAL THERMOMETER |
| 中文描述： | 集成電路釤數字溫度計 |
| 文件頁數： | 5/13頁 |
| 文件大小： | 539K |
| 代理商： | DS1620S |
DS1620
5 of 13
boundary has been met or exceeded, or as part of a closed loop system it can be used to activate a heating
system and deactivate it when the system temperature returns to tolerance.
The T
COM
output goes high when the measured temperature meets or exceeds TH, and will stay high until
the temperature equals or falls below TL. In this way, any amount of hysteresis can be obtained.
THERMOSTAT OUTPUT OPERATION
Figure 3
OPERATION AND CONTROL
The DS1620 must have temperature settings resident in the TH and TL registers for thermostatic
operation. A configuration/status register also determines the method of operation that the DS1620 will
use in a particular application and indicates the status of the temperature conversion operation. The
configuration register is defined as follows:
CONFIGURATION/STATUS REGISTER
where
DONE = Conversion Done Bit. 1=conversion complete, 0=conversion in progress.
THF
to the value of TH. It will remain 1 until reset by writing 0 into this location or by removing power from
the device. This feature provides a method of determining if the DS1620 has ever been subjected to
temperatures above TH while power has been applied.
= Temperature High Flag. This bit will be set to 1 when the temperature is greater than or equal
TLF
the value of TL. It will remain 1 until reset by writing 0 into this location or by removing power from the
device. This feature provides a method of determining if the DS1620 has ever been subjected to
temperatures below TL while power has been applied.
= Temperature Low Flag. This bit will be set to 1 when the temperature is less than or equal to
NVB
memory is not busy. A copy to E
2
may take up to 10 ms.
= Nonvolatile Memory Busy Flag. 1=write to an E
2
memory cell in progress. 0=nonvolatile
CPU
low. If CPU is 1, the DS1620 will be used with a CPU communicating to it over the 3–wire port, and the
= CPU Use Bit. If CPU=0, the CLK/
CONV
pin acts as a conversion start control, when
RST
is
T
HIGH
T
LOW
T
COM
TL
TH
T(°C)
DONE
THF
TLF
NVB
1
0
CPU
1SHOT
相關PDF資料 |
PDF描述 |
|---|---|
| DS1620 | Digital Thermometer and Thermostat |
| DS1629 | 2-Wire Digital Thermometer and Real Time Clock |
| DS1630ABL-70 | NVRAM (Battery Based) |
| DS1630ABL-70-IND | NVRAM (Battery Based) |
| DS1630ABL-85 | NVRAM (Battery Based) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1620S/T&R | 制造商:Maxim Integrated Products 功能描述:DIGITAL THERM. 8P SO 208M TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-SOIC |
| DS1620S/T&R | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1620S+ | 功能描述:板上安裝溫度傳感器 Digital Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS1620S+T&R | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 3-WIRE 8SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC THERMOMETER/STAT DIG 8-SOIC 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Digital Thermometer & Thermostat |
| DS1620S+T&R/C01 | 制造商:Maxim Integrated Products 功能描述:DIGITAL THERMOMETER AND THERMOSTAT - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。