參數資料
型號: DS1395S
英文描述: RAMified Real Time Clock
中文描述: 網狀實時時鐘
文件頁數: 4/19頁
文件大?。?/td> 193K
代理商: DS1395S
DS1395/DS1397
020794 4/19
TIME, CALENDAR AND ALARM LOCATIONS
The time and calendar information is obtained by read-
ing the appropriate register bytes shown in Table 1. The
time, calendar, and alarm are set or initialized by writing
the appropriate register bytes. The contents of the time,
calendar, and alarm registers can be either Binary or
Binary-Coded Decimal (BCD) format. Table 1 shows
the binary and BCD formats of the twelve time, calendar,
and alarm locations.
Before writing the internal time, calendar, and alarm reg-
isters, the SET bit in Register B should be written to a
logic one to prevent updates from occurring while ac-
cess is being attempted. Also at this time, the data for-
mat (binary or BCD), should be set via the data mode bit
(DM) of Register B. All time, calendar, and alarm regis-
ters must use the same data mode. The set bit in Regis-
ter B should be cleared after the data mode bit has been
written to allow the real-time clock to update the time
and calendar bytes.
Once initialized, the real-time clock makes all updates in
the selected mode. The data mode cannot be changed
without reinitializing the ten data bytes. The 24/12 bit
cannot be changed without reinitializing the hour loca-
tions. When the 12-hour format is selected, the high or-
der bit of the hours byte represents PM when it is a logic
one. The time, calendar, and alarm bytes are always ac-
cessible because they are double buffered. Once per
second the ten bytes are advanced by one second and
checked for an alarm condition. If a read of the time and
calendar data occurs during an update, a problem exists
where seconds, minutes, hours, etc. may not correlate.
The probability of reading incorrect time and calendar
data is low. Several methods of avoiding any possible
incorrect time and calendar reads are covered later in
this text.
The three alarm bytes can be used in two ways. First,
when the alarm time is written in the appropriate hours,
minutes, and seconds alarm locations, the alarm inter-
rupt is initiated at the specified time each day if the alarm
enable bit is high . The second method is to insert a
“don’t care” state in one or more of the three alarm bytes.
The “don’t care” code is any hexadecimal value from C0
to FF. The two most significant bits of each byte set the
“don’t care” condition when at logic 1. An alarm will be
generated each hour when the “don’t care” bits are set in
the hours byte. Similarly, an alarm is generated every
minute with “don’t care” codes in the hours and minute
alarm bytes. The “don’t care” codes in all three alarm
bytes create an interrupt every second.
相關PDF資料
PDF描述
DS1402D-41 iButton Probe Component Parts
DS1402 iButton Probe Component Parts
DS1402D-003 iButton Probe Component Parts
DS1402D-010 iButton Probe Component Parts
DS1402D-011 iButton Probe Component Parts
相關代理商/技術參數
參數描述
DS1395SN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC
DS1397 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:RAMified Real Time Clock
DS-14 功能描述:非熱縮管和套管 FLEX BRAIDED SHIELD 14MM X 100M ROLL RoHS:否 制造商:Panduit 產品:Cable Wraps 類型:Spiral 顏色:Black 材料:PP 內徑:0.03 in 長度:100 ft
DS14-00 制造商:FLOWLINE 功能描述:Sensor, Liquid Level, Ultrasonic Switch/Control 4 Relays; Range 49.2 in, 1NPT
DS1-40-0001 制造商:SCHURTER 制造商全稱:Schurter Inc. 功能描述:Storage Choke, fully potted resign