- 您現在的位置：買賣IC網 > PDF目錄376938 > DS1020-50 Programmable 8-Bit Silicon Delay Line PDF資料下載
參數資料
| 型號： | DS1020-50 |
| 英文描述： | Programmable 8-Bit Silicon Delay Line |
| 中文描述： | 可編程8位硅延遲線 |
| 文件頁數： | 2/9頁 |
| 文件大?。?/td> | 193K |
| 代理商： | DS1020-50 |
DS1021
2 of 9
PARALLEL MODE (S = 1)
In the PARALLEL programming mode, the output of the DS1021 will reproduce the logic state of the
input after a delay determined by the state of the 8 program input pins P0 - P7. The parallel inputs can be
programmed using DC levels or computer-generated data. For infrequent modification of the delay value,
jumpers may be used to connect the input pins to V
CC
and ground. For applications requiring frequent
timing adjustment, DIP switches should be used. The enable pin (E) must be at a logic 1 in hardwired
implementations.
Maximum flexibility is obtained when the 8 parallel programming bits are set using computer-generated
data. When the data setup (t
DSE
) and data hold (t
DHE
) requirements are observed, the enable pin can be
used to latch data supplied on an 8-bit bus. Enable must be held at a logic 1 if it is not used to latch the
data. After each change in delay value, a settling time (t
EDV
or t
PDV
) is required before input logic levels
are accurately delayed.
Since the DS1021 is a CMOS design, unused input pins (D and C) must be connected to well-defined
logic levels; they must not be allowed to float.
SERIAL MODE (S = 0)
In the SERIAL programming mode, the output of the DS1021 will reproduce the logic state of the input
after a delay time determined by an 8-bit value clocked into serial port D. While observing data setup
(t
DSC
) and data hold (t
DHC
) requirements, timing data is loaded in MSB-to-LSB order by the rising edge of
the serial clock (C). The enable pin (E) must be at a logic 1 to load or read the internal 8-bit input register,
during which time the delay is determined by the last value activated. Data transfer ends and the new
delay value is activated when enable (E) returns to a logic 0. After each change, a settling time (t
EDV
) is
required before the delay is accurate.
As timing values are shifted into the serial data input (D), the previous contents of the 8-bit input register
are shifted out of the serial output pin (Q) in MSB-to-LSB order. By connecting the serial output of one
DS1021 to the serial input of a second DS1021, multiple devices can be daisy-chained (cascaded) for
programming purposes (Figure 3). The total number of serial bits must be eight times the number of units
Applications can read the setting of the DS1021 delay line by connecting the serial output pin (Q) to the
serial input (D) through a resistor with a value of 1K to 10K ohms (Figure 2). Since the read process is
destructive, the resistor restores the value read and provides isolation when writing to the device. The
resistor must connect the serial output (Q) of the last device to the serial input (D) of the first device of a
daisy-chain (Figure 3). For serial readout with automatic restoration through a resistor, the device used to
write serial data must go to a high impedance state.
To initiate a serial read, enable (E) is taken to a logic 1 while serial clock (C) is at a logic 0. After a
waiting time (t
EQV
), bit 7 (MSB) appears on the serial output (Q). On the first rising (0
→
1) transition of
the serial clock (C), bit 7 (MSB) is rewritten and bit 6 appears on the output after a time t
CQV
. To restore
the input register to its original state, this clocking process must be repeated eight times. In the case of a
daisy-chain, the process must be repeated eight times per package. If the value read is restored before
enable (E) is returned to logic 0, no settling time (t
EDV
) is required and the programmed delay remains
unchanged.
Since the DS1021 is a CMOS design, unused input pins (P1 - P7) must be connected to well-defined logic
levels; they must not be allowed to float. Serial output Q/P0 should be allowed to float if unused.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1021-25 | ENDPLATE FOR SRU4/SR4-T15/SRM4 |
| DS1021-50 | Programmable 8-Bit Silicon Delay Line |
| DS1023-025 | 8-Bit Programmable Timing Element |
| DS1023-050 | 8-Bit Programmable Timing Element |
| DS1023-100 | 8-Bit Programmable Timing Element |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS10-20B | 制造商:TRANSMISSION DEVELOPMENTS 功能描述:MOULDED SPUR GEAR 1.0, 20 |
| DS1020G-025 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable Delay Line |
| DS1020G-050 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable Delay Line |
| DS1020G-100 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable Delay Line |
| DS1020G-200 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Programmable Delay Line |
發布緊急采購，3分鐘左右您將得到回復。