- 您現在的位置：買賣IC網 > PDF目錄376802 > DM9102A (Electronic Theatre Controls, Inc.) Single Chip Fast Ethernet NIC controller PDF資料下載
參數資料
| 型號： | DM9102A |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Single Chip Fast Ethernet NIC controller |
| 中文描述： | 單芯片快速以太網網卡控制器 |
| 文件頁數： | 58/77頁 |
| 文件大?。?/td> | 459K |
| 代理商： | DM9102A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁
DM9102A
Single Chip Fast Ethernet NIC controller
58
Final
Version: DM9102A-DS-F03
August 28, 2000
Power Management
1. Overview
The DM9102A supports power management mechanism. It
complies with the ACPI Specification Rev 1.0, the Network
Device Class Power Management Specification Rev 1.0,
and PCI Bus Power Management Interface Specification
Rev 1.0. In addition, it also support Wake-On LAN (WOL)
which is the features of the AMD’s Magic Packet
technology. With this function, it can wake-up a remote
sleeping station.
2. PCI Function Power Management States
The DM9102A supports PCI function power states D0,
D3(hot), D3(cold), and not supports D1, D2 states.
Additional PCI signal PME# (power management event,
open drain) to pin A19 of the standard PCI connector.
D0:
normal & fully functional state
D3(hot) :
For controller, configuration space can be
accessed and wake-up on LAN circuit can be enabled.
PME# operational circuit is active, full function is supported
to detect the wake-up Frame & Link status. Because of
functions in D3(hot) must respond to configuration space
accesses as long as power and clock are supplied so that
they can be returned to D0 state by software.
D3(cold) :
If Vcc is removed from a PCI device, all of its PCI
functions transition immediately to D3(cold), no bus
transaction is active under no pci_clk condition and wake-up
on LAN operation should be alive. PME# operational circuit
is active. Full function is supported under auxiliary power to
detect the wake-up Frame & Link status. When power
restored, PCI RST# must be asserted and functions will
return to D0 with a full PCI Spec. 2.2 compliant power-on
reset sequence. The power required in D3(cold) must be
provided by some auxiliary power source.
3. The Power Management Operation
It complies with the PCI Bus Power Management Interface
Specification Rev. 1.0. The Power Management Event
(PME#) signal is an optional open drain, active low signal
that is intended to be driven low by a PCI function to request
a change in its current power management state and/or to
indicate that a power management event has occurred.
The PME# signal has been assigned to pin A19 of the
standard PCI Connector configuration. The assertion and
de-assertion of PME# is asynchronous to the PCI clock.
Software will enable its use by setting the PME_En bit in the
PMCSR (write 1 to PMCSR<8>). When a PCI function
generates or detects an event that requires the system to
change its power state, the function will assert PME#. It
must continue to assert PME# until software either clears
the PME_En bit (PMCSR<8> is set to 0) or clears the
PME_Status bit in the PMCSR (write 1 to PMCSR<15>).
DM9102A support three main categories of network device
wake-up events specified in Network Device Class Power
Management Rev1.0. That is, the DM9102A can monitor
the network for a Link Change, Magic Packet or a Wake-up
Frame and notify the system by generating PME# if any of
three events occurs. Program the PCIUSR (offset = 40h)
can select the PME# event, and write 1 to PMCSR<15> will
clear the PME#.
a. Detect Network Link State Change
Any link status change will set the wake-up event.
1. Writes 1 into PMCSR<15>(54h) to clear previous PME#
status
2. Writes 1 into PMCSR<8> to enable PME# function
3. Writes 1 into PCIUSR<29> to enable the link status
change function
b. Active Magic Packet Function
Could be optionally enabled from EEPROM contents. Send
a setup frame with a magic node address at first filter
address using perfect address filtering mode.
1. Writes 1 into PMCSR<15> to clear previous PME status
2. Writes 1 into PMCSR<8> to enable PME# function
3. Writes 1 into PCIUSR<27> to enable magic packet
function.
c. Active the Sample Frame Function
Could be optionally enabled from PCIUSR<28>. Sample
frame data and corresponding byte mask are loaded into
transmit FIFO & receive FIFO before entering D3(hot). The
software driver has to stop the TX/RX process before setting
the sample frame and byte mask into the FIFO. Transmit &
相關PDF資料 |
PDF描述 |
|---|---|
| DM9102AF | Single Chip Fast Ethernet NIC controller |
| DM9102AT | Single Chip Fast Ethernet NIC controller |
| DM9108APPLICATIONENGINEERINGNOTESONE | DM9108 Application Engineering notes one |
| DM9108APPLICATIONENGINEERINGNOTESTHREE | DM9108 Application Engineering notes three |
| DM9108APPLICATIONENGINEERINGNOTESTWO | DM9108 Application Engineering notes two |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DM9102AF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single Chip Fast Ethernet NIC controller |
| DM9102AT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single Chip Fast Ethernet NIC controller |
| DM9102D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE CHIP FAST ETHEMET NIC CONTROLLER |
| DM9102DE | 制造商:DAVICOM 制造商全稱:DAVICOM 功能描述:Single Chip Fast Ethernet NIC Controller |
| DM9102DEP | 制造商:DAVICOM 功能描述:IC ENET CNTRL 10/100M PHY 1 制造商:DAVICOM 功能描述:IC ENET CNTRL 10/100M PHY 128LQFP 制造商:DAVICOM 功能描述:IC, ENET CNTRL, 10/100M PHY, 128LQFP 制造商:DAVICOM 功能描述:IC, ENET CNTRL, 10/100M PHY, 128LQFP; Data Rate:100Mbps; Ethernet Type:IEEE 802.3u; Supply Voltage Min:2.375V; Supply Voltage Max:2.625V; Digital IC Case Style:LQFP; No. of Pins:128; Interface Type:PCI; Operating Temperature Min:0C;;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。