- 您現在的位置：買賣IC網 > PDF目錄15535 > DM164134 (Microchip Technology)KIT DEV PIC18F4XK22 PDF資料下載
參數資料
| 型號： | DM164134 |
| 廠商： | Microchip Technology |
| 文件頁數： | 77/116頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT DEV PIC18F4XK22 |
| 標準包裝： | 1 |
| 系列： | PIC® 18F |
| 類型： | MCU |
| 適用于相關產品： | PIC18F4XK22，PIC18F2XK22 |
| 所含物品： | 板，文檔 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁當前第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
2006 Microchip Technology Inc.
DS41159E-page 61
PIC18FXX8
5.3
Reading the Data EEPROM
Memory
To read a data memory location, the user must write the
address to the EEADR register, clear the EEPGD and
CFGS control bits (EECON1<7:6>) and then set
control bit RD (EECON1<0>). The data is available in
the very next instruction cycle of the EEDATA register;
therefore, it can be read by the next instruction.
EEDATA will hold this value until another read
operation or until it is written to by the user (during a
write operation).
EXAMPLE 5-1:
DATA EEPROM READ
5.4
Writing to the Data EEPROM
Memory
To write an EEPROM data location, the address must
first be written to the EEADR register and the data writ-
ten to the EEDATA register. Then, the sequence in
Example 5-2 must be followed to initiate the write cycle.
The write will not initiate if the above sequence is not
exactly followed (write 55h to EECON2, write 0AAh to
EECON2, then set WR bit) for each byte. It is strongly
recommended that interrupts be disabled during this
code segment.
Additionally, the WREN bit in EECON1 must be set to
enable writes. This mechanism prevents accidental
writes to data EEPROM due to unexpected code exe-
cution (i.e., runaway programs). The WREN bit should
be kept clear at all times, except when updating the
EEPROM. The WREN bit is not cleared by hardware.
After a write sequence has been initiated, clearing the
WREN bit will not affect the current write cycle. The WR
bit will be inhibited from being set unless the WREN bit
is set. The WREN bit must be set on a previous instruc-
tion. Both WR and WREN cannot be set with the same
instruction.
At the completion of the write cycle, the WR bit is
cleared in hardware and the EEPROM Write Complete
Interrupt Flag bit (EEIF) is set. The user may either
enable this interrupt or roll this bit. EEIF must be
cleared by software.
EXAMPLE 5-2:
DATA EEPROM WRITE
MOVLW
DATA_EE_ADDR
;
MOVWF
EEADR
;Data Memory Address
;to read
BCF
EECON1, EEPGD
;Point to DATA memory
BCS
EECON1, CFGS
;
BSF
EECON1, RD
;EEPROM Read
MOVF
EEDATA, W
;W = EEDATA
MOVLW
DATA_EE_ADDR
;
MOVWF
EEADR
; Data Memory Address to read
MOVLW
DATA_EE_DATA
;
MOVWF
EEDATA
; Data Memory Value to write
BCF
EECON1, EEPGD
; Point to DATA memory
BCF
EECON1, CFGS
; Access program FLASH or Data EEPROM memory
BSF
EECON1, WREN
; Enable writes
BCF
INTCON, GIE
; Disable interrupts
Required
MOVLW
55h
;
Sequence
MOVWF
EECON2
; Write 55h
MOVLW
0AAh
;
MOVWF
EECON2
; Write AAh
BSF
EECON1, WR
; Set WR bit to begin write
BSF
INTCON, GIE
; Enable interrupts
.
; user code execution
.
BCF
EECON1, WREN
; Disable writes on write complete (EEIF set)
相關PDF資料 |
PDF描述 |
|---|---|
| AIUR-07-221K | INDUCTOR POWER 220UH 10% T/H |
| MAX8903CETI+ | IC DC/DC CHARGER LI+ 2A 28-TQFN |
| MAX11080GUU/V+T | IC LI/BATTERY MANAGEMENT 38TSSOP |
| MAX11081GUU+T | IC FAULT MON BATT 12CH 38-TSSOP |
| MAX11081GUU/V+T | IC FAULT MON BATT 12CH 38TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DM164135 | 制造商:Microchip Technology Inc 功能描述:KIT, ONEPIC DEMO BOARD, PLUS PICKIT 3 制造商:Microchip Technology Inc 功能描述:KIT, ONEPIC DEMO BOARD, PLUS PICKIT 3; SVHC:No SVHC (19-Dec-2012) ;RoHS Compliant: Yes 制造商:Microchip Technology Inc 功能描述:One PIC MCU Platform Board with PICkit 3 |
| DM164135 | 制造商:Microchip Technology Inc 功能描述:PICKIT 3 IN-CIRCUIT DEBUGGER |
| DM173001 | 功能描述:開發板和工具包 - PIC / DSPIC PICDEM 17 PIC17CXX RoHS:否 制造商:Microchip Technology 產品:Starter Kits 工具用于評估:chipKIT 核心:Uno32 接口類型: 工作電源電壓: |
| DM180021 | 功能描述:開發板和工具包 - PIC / DSPIC PIC18 Starter Kit RoHS:否 制造商:Microchip Technology 產品:Starter Kits 工具用于評估:chipKIT 核心:Uno32 接口類型: 工作電源電壓: |
| DM1800-434MB | 功能描述:射頻模塊 DM1800 Base Station 433.92 MHz RoHS:否 制造商:Linx Technologies 產品:Transceiver Modules 頻帶:902 MHz to 928 MHz 輸出功率:- 15.5 dBm to + 12.5 dBm 接口類型:UART 工作電源電壓:- 0.3 VDC to + 5.5 VDC 傳輸供電電流:38.1 mA 接收供電電流:22.7 mA 天線連接器類型:U.FL 最大工作溫度:+ 85 C 尺寸:1.15 mm x 0.63 mm x 0.131 mm |
發布緊急采購，3分鐘左右您將得到回復。