參數資料
型號： DEMOMPR083
廠商： Freescale Semiconductor
文件頁數： 34/35頁
文件大?。?/td> 0K
描述： BOARD DEMO FOR MPR083 CTLR
產品培訓模塊： Sensor Toolbox
標準包裝： 1
傳感器類型： 觸摸，電容式
傳感范圍： 8 個按鈕/鍵
接口： I²C
電源電壓： 1.8 V ~ 3.6 V
嵌入式： 是，MCU，8 位
已供物品： 板，電池
已用 IC / 零件： MPR083
產品目錄頁面： 2808 (CN2011-ZH PDF)
相關產品： MPR083EJR2CT-ND - IC CTLR TOUCH SENSR PROX 16TSSOP
MPR083QR2-ND - IC CTLR TOUCH SENSOR PROX 16-QFN
MPR083Q-ND - IC CTLR TOUCH SENSOR PROX 16-QFN
MPR083EJR2TR-ND - IC CTLR TOUCH SENSR PROX 16TSSOP
MPR083EJ-ND - IC CTLR TOUCH SENSR PROX 16TSSOP
MPR083
Sensors
8
Freescale Semiconductor
When performing read-after-write verification, remember to re-set the command byte’s address because the stored command
byte address will generally have been auto-incremented after the write (Section 2.4).
Figure 12. ‘n’ Data Bytes Received
2.3.8
Operation with Multiple Master
The application should use repeated starts to address the MPR083 to avoid bus confusion between I2C masters.On a I2C bus,
once a master issues a start/repeated start condition, that master owns the bus until a stop condition occurs. If a master that does
not own the bus attempts to take control of that bus, then improper addressing may occur. An address may always be rewritten
to fix this problem. Follow I2C protocol for multiple master configurations.
2.3.9
Device Reset
The RST is an active-low software reset. This is implemented in the Configuration Register by activating the RST bit. When
asserted, the device clears any transaction to or from the MPR083 on the serial interface and configures the internal registers to
the same state as a power-up reset (Table 4). The MPR083 then waits for a START condition on the serial interface.
The sensor controller is capable of operating down to 1.8 V, however, in order for the sensor controller to exit reset and startup
correctly the host system must initially provide 2.0 V to 3.6 V input to VDD and then follow the process in Figure 13. This process
is required in applications that require regulated operation in the 1.8 V to 2.0 V range. In the case that the application uses an
unregulated battery, then the battery must initially provide at least 2.0 V to correctly power-up the sensor controller which limits
battery selection to the 2.0 V to 3.6 V range.
Figure 13. Low Voltage (1.8 V - 2.0 V) Power-up Sequence
SAAA P
1
SLAVE ADDRESS
COMMAND BYTE
DATA BYTE
acknowledge from MPR083
R/W
nbytes
auto-increment memory
word address
D15 D14 D13 D12 D11 D10 D9 D8
D1 D0
D3 D2
D5 D4
D7 D6
Howcommand byte and data byte
map into MPR083's registers
acknowledge from
MPR083
acknowledge from
MPR083
Established Comms with
Sensor Controller?
i.e. Read from FIFO
Is Data valid? (0 x 40)
Idle Delay Loop
Apply 2.0V to VDD Max
To Sensor Controller
Lower VDD to the desired operating voltage
1.8 V to 2.0 V
False
True
相關PDF資料
PDF描述
0210390880 CABLE JUMPER 1MM .076M 19POS
EEM28DTBI CONN EDGECARD 56POS R/A .156 SLD
ADR02ARZ-REEL IC VREF SERIES PREC 5V 8-SOIC
EA-OEM-410 KIT LPC3250 259 WITH QVGA
VI-J7P-EZ CONVERTER MOD DC/DC 13.8V 25W
相關代理商/技術參數
參數描述
DEMO-MSA 制造商:Avago Technologies 功能描述:DEMOBOARD MSA-XX05,10,11,36,70,86 - Bulk
DEMONB5CP1V1 制造商:OMRON AUTOMATION AND SAFETY 功能描述:NB5 CP1 PLC SALES DEMO
DEMO-NB5CP1V1 制造商:OMRON AUTOMATION AND SAFETY 功能描述:NB5 CP1 PLC SALES DEMO 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:NB5 CP1 PLC Sales Demo
DEMO-NB7CP1V1 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:NB7 CP1 PLC Sales Demo
DEMO-NJ51-KIT-ECT-0-V1 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:NJ5 Demo UGKIT, TJG5ML2 to NJE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*