- 您現在的位置：買賣IC網 > PDF目錄17032 > DC1082A-D (Linear Technology)BOARD SAR ADC LTC1403A PDF資料下載
參數資料
| 型號： | DC1082A-D |
| 廠商： | Linear Technology |
| 文件頁數： | 5/20頁 |
| 文件大小： | 0K |
| 描述： | BOARD SAR ADC LTC1403A |
| 軟件下載： | QuikEval II System |
| 設計資源： | DC1082A Design File DC1082A Schematic |
| 標準包裝： | 1 |
| 系列： | QuikEval-II™ |
| ADC 的數量： | 1 |
| 位數： | 14 |
| 采樣率（每秒）： | 3M |
| 數據接口： | 串行，SPI? |
| 輸入范圍： | 0 ~ 2.5 V |
| 已用 IC / 零件： | LTC1403 |
| 已供物品： | 板 |
| 相關產品： | LTC1403HMSE#TRPBF-ND - IC ADC 12BIT 2.8MSPS DIFF 10MSOP LTC1403HMSE#PBF-ND - IC ADC 12BIT 2.8MSPS DIFF 10MSOP LTC1403AHMSE#TRPBF-ND - IC ADC 14BIT 2.8MSPS DIFF 10MSOP LTC1403AHMSE#PBF-ND - IC ADC 14BIT 2.8MSPS DIFF 10MSOP LTC1403ACMSE#PBF-ND - IC ADC 14BIT 2.8MSPS 10-MSOP LTC1403AIMSE-1#PBF-ND - IC ADC 14BIT 2.8MSPS 10-MSOP LTC1403ACMSE-1#PBF-ND - IC ADC 14BIT 2.8MSPS 10-MSOP LTC1403CMSE#PBF-ND - IC ADC 12BIT 2.8MSPS 10-MSOP LTC1403AIMSE#PBF-ND - IC ADC 14BIT 2.8MSPS 10-MSOP LTC1403IMSE#PBF-ND - IC ADC 12BIT 2.8MSPS 10-MSOP 更多... |
LTC1403/LTC1403A
13
1403fb
APPLICATIONS INFORMATION
intervening rising edges at SCK, put the LTC1403/LTC1403A
in Sleep mode and the power drain drops from 16mW
to 10μW. One or more rising edges at SCK wake up the
LTC1403/LTC1403A for operation. The internal reference
(VREF) takes 2ms to slew and settle with a 10μF load.
Note that, using sleep mode more frequently than every
2ms, compromises the settled accuracy of the internal
reference. Note that, for slower conversion rates, the Nap
and Sleep modes can be used for substantial reductions
in power consumption.
DIGITAL INTERFACE
The LTC1403/LTC1403A has a 3-wire SPI (Serial Protocol
Interface) interface. The SCK and CONV inputs and SDO
output implement this interface. The SCK and CONV inputs
accept swings from 3V logic and are TTL compatible, if the
logic swing does not exceed VDD. A detailed description
of the three serial port signals follows:
Conversion Start Input (CONV)
The rising edge of CONV starts a conversion, but subse-
quent rising edges at CONV are ignored by the LTC1403/
LTC1403A until the following 16 SCK rising edges have
occurred. It is necessary to have a minimum of 16 rising
edges of the clock input SCK between rising edges of CONV.
But to obtain maximum conversion speed, it is necessary
to allow two more clock periods between conversions to
allow 39ns of acquisition time for the internal ADC sample-
and-hold circuit. With 16 clock periods per conversion,
the maximum conversion rate is limited to 2.8Msps to
allow 39ns for acquisition time. In either case, the output
data stream comes out within the rst 16 clock periods to
ensure compatibility with processor serial ports. The duty
cycle of CONV can be arbitrarily chosen to be used as a
frame sync signal for the processor serial port. A simple
approach to generate CONV is to create a pulse that is
one SCK wide to drive the LTC1403/LTC1403A and then
buffer this signal with the appropriate number of inverters
to ensure the correct delay driving the frame sync input of
the processor serial port. It is good practice to drive the
LTC1403/LTC1403A CONV input rst to avoid digital noise
interference during the sample-to-hold transition triggered
by CONV at the start of conversion. It is also good practice
to keep the width of the low portion of the CONV signal
greater than 15ns to avoid introducing glitches in the front
end of the ADC just before the sample-and-hold goes into
hold mode at the rising edge of CONV.
Minimizing Jitter on the CONV Input
In high speed applications where high amplitude sinewaves
above 100kHz are sampled, the CONV signal must have
as little jitter as possible (10ps or less). The square wave
output of a common crystal clock module usually meets
this requirement easily. The challenge is to generate a CONV
signal from this crystal clock without jitter corruption from
other digital circuits in the system. A clock divider and
any gates in the signal path from the crystal clock to the
CONV input should not share the same integrated circuit
with other parts of the system. As shown in the interface
circuit examples, the SCK and CONV inputs should be
driven rst, with digital buffers used to drive the serial port
interface. Also note that the master clock in the DSP may
already be corrupted with jitter, even if it comes directly
from the DSP crystal. Another problem with high speed
processor clocks is that they often use a low cost, low
speed crystal (i.e., 10MHz) to generate a fast, but jittery,
phase-locked-loop system clock (i.e., 40MHz). The jitter
in these PLL-generated high speed clocks can be several
nanoseconds. Note that if you choose to use the frame
sync signal generated by the DSP port, this signal will
have the same jitter of the DSP’s master clock.
Serial Clock Input (SCK)
The rising edge of SCK advances the conversion process
and also udpates each bit in the SDO data stream. After
CONV rises, the third rising edge of SCK starts clocking out
the 12/14 data bits with the MSB sent rst. A simple ap-
proach is to generate SCK to drive the LTC1403/LTC1403A
相關PDF資料 |
PDF描述 |
|---|---|
| STD17W-I | WIRE & CABLE MARKERS |
| GBM22DCAT | CONN EDGECARD 44POS R/A .156 SLD |
| DC1082A-C | BOARD SAR ADC LTC1403A-1 |
| TFL0816-56N | INDUCTOR 56NH +/-2% 0603 |
| STD17W-E | WIRE & CABLE MARKERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC1082A-E | 功能描述:BOARD SAR ADC LTC2356-14 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:QuikEval-II™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC1082A-F | 功能描述:BOARD SAR ADC LTC2355-14 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:QuikEval-II™ 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| DC1083A-A | 功能描述:BOARD DEMO LTM4603 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:µModule® 標準包裝:1 系列:- 主要目的:DC/DC，步降 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:3.3V 電流 - 輸出:3A 輸入電壓:4.5 V ~ 28 V 穩壓器拓撲結構:降壓 頻率 - 開關:250kHz 板類型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名稱:497-12113STEVAL-ISA094V1-ND |
| DC1083A-B | 功能描述:BOARD DEMO LTM4603HV RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:µModule® 標準包裝:1 系列:- 主要目的:DC/DC，步降 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:3.3V 電流 - 輸出:3A 輸入電壓:4.5 V ~ 28 V 穩壓器拓撲結構:降壓 頻率 - 開關:250kHz 板類型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名稱:497-12113STEVAL-ISA094V1-ND |
| DC1084A-A | 功能描述:BOARD DEMO LTM4602 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:µModule® 標準包裝:1 系列:- 主要目的:DC/DC，步降 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:3.3V 電流 - 輸出:3A 輸入電壓:4.5 V ~ 28 V 穩壓器拓撲結構:降壓 頻率 - 開關:250kHz 板類型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名稱:497-12113STEVAL-ISA094V1-ND |
發布緊急采購，3分鐘左右您將得到回復。