- 您現在的位置：買賣IC網 > PDF目錄1909 > CS61884-IRZ (Cirrus Logic Inc)IC LN INTERF T1/E1/J1 160-LFBGA PDF資料下載
參數資料
| 型號： | CS61884-IRZ |
| 廠商： | Cirrus Logic Inc |
| 文件頁數： | 21/72頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LN INTERF T1/E1/J1 160-LFBGA |
| 標準包裝： | 126 |
| 功能： | 線路接口單元（LIU） |
| 接口： | E1，J1，T1 |
| 電路數： | 8 |
| 電源電壓： | 3.14 V ~ 3.47 V |
| 功率（瓦特）： | 1.73W |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 160-LFBGA |
| 供應商設備封裝： | 160-TFGBA（13x13） |
| 包裝： | 散裝 |
| 包括： | AMI 編碼器和解碼器，B8ZS 編碼器和解碼器，HDB3 編碼器和解碼器，LOS 檢測 |
| 產品目錄頁面： | 759 (CN2011-ZH PDF) |
| 其它名稱： | 598-1717 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
CS61884
28
DS485F3
During host mode operation, LOS is reported in the
LOS Status Monitor Register. Both the LOS pins
and the register bits reflect LOS status in host mode
operation. The LOS pins and status bits are set high
(indicating loss of signal) during reset, power-up,
or channel powered-down.
10.6 Alarm Indication Signal (AIS)
The CS61884 detects all ones alarm condition per
the relevant ANSI, ITU, and ETSI specifications.
In general, AIS is indicated when the one’s density
of the receive signal exceeds that dictated by the
relevant specification. This feature is only avail-
able in host mode (Refer to LOS/AIS Mode En-
ANSI T1.231 AIS (T1/J1 Mode) - The AIS condi-
tion is declared when less than 9 zeros are received
within a sliding window of 8192 bits. This corre-
sponds to a ones density of 99.9% over a period of
5.3 ms. The AIS condition is cleared when nine or
more zeros are detected in a sliding window of
8192 bits.
ITU G.775 AIS (E1 Mode) - The AIS condition is
declared when less than 3 zeros are received within
two consecutive 512 bit windows. The AIS condi-
tion is cleared when 3 or more zeros are received in
two consecutive 512 bit windows.
ETSI 300 233 (E1 Mode) - The AIS condition is
declared when less than 3 zeros are received in a
512 bit window. The AIS condition is cleared when
a 512 bit window is received containing 3 or more
zeros.
11. JITTER ATTENUATOR
The CS61884 internal jitter attenuators can be
switched into either the receive or transmit paths.
Alternatively, it can be removed from both paths to
reduce the propagation delay.
During Hardware mode operation, the location of
the jitter attenuator for all eight channels are con-
trolled by the JASEL pin (Refer to Table 6 for pin
configurations). The jitter attenuator’s FIFO length
and corner frequency, can not be changed in hard-
ware mode. The FIFO length and corner frequency
are set to 32 bits and 1.25Hz for the E1 operational
modes and to 32 bits and 3.78Hz in the T1/J1 oper-
ational modes.
During host mode operation, the location of the jit-
ter attenuator for all eight channels are set by bits 0
and 1 in the Global Control Register (0Fh) (See
Section 14.16 on page 38). The GLOBAL CON-
TROL REGISTER (0Fh) also configures the jitter
attenuator’s FIFO length (bit 3) and corner fre-
quency (bit 2).
The attenuator consists of a 64-bit FIFO, a narrow-
band monolithic PLL, and control logic. The jitter
attenuator requires no external crystal. Signal jitter
is absorbed in the FIFO which is designed to nei-
ther overflow nor underflow.
If overflow or underflow is imminent, the jitter
transfer function is altered to ensure that no bit-er-
rors occur. A configuration option is provided to
reduce the jitter attenuator FIFO length from 64
bits to 32 bits in order to reduce propagation delay.
The jitter attenuator -3 dB knee frequency depends
on the settings of the Jitter Attenuator FIFO length
and the Jitter Attenuator Corner Frequency bits 2
and 3, in the Global Control Register (0Fh) (See
Section 14.16 on page 38)). Setting the lowest cor-
ner frequency guarantees jitter attenuation compli-
ance to European specifications TBR 12/13 and
ETSI ETS 300 011 in E1 mode. The jitter attenua-
tor is also compliant with ITU-T G.735, G.742,
G.783 and AT&T Pub. 62411 (Refer to Figure 19
Table 6. Jitter Attenuator Configurations
PIN STATE
JITTER ATTENUATOR POSITON
LOW
Transmit Path
HIGH
Receive Path
OPEN
Disabled
相關PDF資料 |
PDF描述 |
|---|---|
| CS8130-CS | IC IR TRANSCEIVER 2-5V 20-SSOP |
| CS8190EDWF20G | IC TACH/SPEEDO DRVR PREC 20SOICW |
| CS8191XNF16 | IC DRVR AIRCORE TACH/SPEED 16DIP |
| CS82C5296 | IC UART/BRG 5V 16MHZ 28-PLCC |
| CS82C59A-1296 | IC CTRL INTERRUPT 12.5MHZ 28PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS61884-IRZR | 功能描述:網絡控制器與處理器 IC IC Octal T1/E1/J1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| CS6193-000 | 功能描述:多芯電纜 RoHS:否 制造商:Alpha Wire 導體數量:3 線規 - 美國線規（AWG）:16 絞合:19 x 29 屏蔽:Shielded 長度:100 ft 電壓額定值:600 V 外殼材料:Polytetrafluoroethylene (PTFE) 絕緣材料:Polytetrafluoroethylene (PTFE) 類型:Communication and Control |
| CS61N | 功能描述:CM SCREWDRIVER,6IN1,INTERCHANGEA 制造商:apex tool group 系列:* 零件狀態:在售 標準包裝:1 |
| CS62 | 制造商:Thomas & Betts 功能描述:Cable Accessories Compression Splice Aluminum |
| CS6-20 | 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:POWER TRANSFORMER |
發布緊急采購，3分鐘左右您將得到回復。