Serial Port Initialization The serial port is initialized to the command mode whenever a power-on reset is performed or when " />
參數資料
型號： CS5529-ASZR
廠商： Cirrus Logic Inc
文件頁數： 7/31頁
文件大?。?/td> 0K
描述： IC ADC 16BIT W/6BIT LATCH 20SSOP
標準包裝： 1,000
位數： 16
數據接口： 串行
轉換器數目： 1
功率耗散（最大）： 3.5mW
電壓電源： 雙 ±
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 20-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 20-SSOP
包裝： 帶卷 (TR)
輸入數目和類型： 1 個差分，單極；1 個差分，雙極
配用： 598-1015-ND - EVAL BOARD FOR CS5529
CS5529
DS246F5
15
Serial Port Initialization
The serial port is initialized to the command mode
whenever a power-on reset is performed or when
the port initialization sequence is completed. The
port initialization sequence involves clocking fif-
teen (or more) SYNC1 command bytes (0xFF) fol-
lowed by one SYNC0 command byte (0xFE). This
sequence places the chip in the command mode
where it waits until a valid command is received.
This function does not reset the internal registers to
their default settings. It only resets the serial port to
the command mode.
System Initialization
When power to the CS5529 is applied, the chip is
held in a reset condition until the 32.768 kHz oscil-
lator has started and a counter-timer elapses. Due to
the high Q of the 32.768 kHz crystal, the oscillator
takes 400-600 ms to start. The counter-timer counts
1002 oscillator clock cycles to make sure the oscil-
lator is fully stable. During this time-out period the
serial port logic is reset and the RV (Reset Valid)
bit in the configuration register is set to indicate
that a valid reset occurred. After a reset, the on-chip
registers are initialized to the following states and
the converter is placed in the command mode
where it waits for a valid command.
Note:
A system reset can be initiated at any time by
writing a logic 1 to the RS (Reset System) bit
in the configuration register. After a reset, the
RV (Reset Valid) bit is set until the
configuration register is read. The user must
then write a logic 0 to the RS bit to take the
part out of the reset mode.
Configuration Register
The configuration register is a 24 bit register used
to modify the functions of the ADC. The following
sections detail the functions of the bits in the con-
figuration register.
Latch Output Pins
The D3-D0 pins of the converter mimic the D21-
D18 bits of the configuration register. D3-D0 can
be used to control multiplexers and other digital
logic functions outside the converter. The D0-D3
outputs are powered from VD+ and DGND. Their
output voltage will be VD+ for a logic 1 and
DGND for a logic 0. The A1-A0 pins of the con-
verter mimic the D23-D22 bits of the configuration
register and can be used to control analog switches.
These outputs are powered from VA+ and VA-,
hence, their output voltage will be either VA+ for a
logic 1 or VA- for a logic 0.
All outputs can sink or source at least 1 mA, but it
is recommended to limit drive currents to less than
20
A to reduce self-heating of the chip.
Power Consumption
The CS5529 accommodates four power consump-
tion modes: normal, low power, standby, and sleep.
The normal mode, the default mode, is entered after
a power-on-reset and typically consumes 2.5 mW.
The low power mode is an alternate mode that re-
duces the consumed power to 1.4 mW. It is entered
by setting bit D16 (the low power mode bit) in the
configuration register to logic 1. Since the convert-
er’s noise and linearity performance improves with
increased power consumption, slightly degraded
noise or linearity performance should be expected
in the low power mode.
The final two modes are the power save modes.
These modes power down most of the analog por-
tion of the chip and stop filter convolutions. The
power save modes are entered whenever the Power
Save (0x81 hexadecimal) command is issued to the
serial port. The particular power save mode entered
depends on state of bit D4 (the power save select
bit) in the configuration register. If D4 is logic 0,
the converter enters the standby mode reducing the
power consumption to 1 mW. The standby mode
leaves the oscillator and the on-chip bias generator
Configuration Register:
000040(H)
Offset Register:
000000(H)
Gain Register:
400000(H)
相關PDF資料
PDF描述
CS5530-ISZR IC ADC 24BIT 1CH W/LNA 20-SSOP
CS5534-ASZR IC ADC 24BIT 4CH W/LNA 24-SSOP
CS5534-BSZR IC ADC 24BIT 4CH W/LNA 24SSOP
CS5550-ISZR IC ADC 2CH LOW-COST 24-SSOP
CS5565-ISZ IC ADC DELTA-SIGMA 24BIT 24-SSOP
相關代理商/技術參數
參數描述
CS5530 制造商:Texas Instruments 功能描述:
CS5530_0911 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:24-bit ADC with Ultra-low-noise Amplifier
CS5530A 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:AMD Geode CS5530A Companion Device
CS5530A-UCE 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:AMD Geode CS5530A Companion Device
CS5530A-UCE B1 制造商:Advanced Micro Devices 功能描述:DICCX5530
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*