- 您現在的位置：買賣IC網 > PDF目錄374167 > CS5166HGDWR16 (ZF Electronics Corporation) 5-Bit Synchronous CPU Controller with Power-Good and Current Limit PDF資料下載
參數資料
| 型號： | CS5166HGDWR16 |
| 廠商： | ZF Electronics Corporation |
| 英文描述： | 5-Bit Synchronous CPU Controller with Power-Good and Current Limit |
| 中文描述： | 5位同步CPU，具有功率控制器，準確和電流限制 |
| 文件頁數： | 19/22頁 |
| 文件大小： | 435K |
| 代理商： | CS5166HGDWR16 |
19
Response Time to Load Decrease
(limited by Inductor value)
Response Time =
Example: V
OUT
= +2.8V, 14.2A change in Load Current,
L = 1.2μH
Response Time =
= 6.1μs
Input and Output Capacitors
These components must be selected and placed carefully to
yield optimal results. Capacitors should be chosen to pro-
vide acceptable ripple on the input supply lines and regu-
lator output voltage. Key specifications for input capacitors
are their ripple rating, while ESR is important for output
capacitors. For best transient response, a combination of
low value/high frequency and bulk capacitors placed close
to the load will be required.
Thermal Considerations for Power MOSFETs and Diodes
In order to maintain good reliability, the junction tempera-
ture of the semiconductor components should be kept to a
maximum of 150°C or lower. The thermal impedance
(junction to ambient) required to meet this requirement can
be calculated as follows:
Thermal Impedance =
A heatsink may be added to TO-220 components to reduce
their thermal impedance. A number of PC board layout
techniques such as thermal vias and additional copper foil
area can be used to improve the power handling capability
of surface mount components.
EMI Management
As a consequence of large currents being turned on and off
at high frequency, switching regulators generate noise as a
consequence of their normal operation. When designing
for compliance with EMI/EMC regulations, additional
components may be added to reduce noise emissions.
These components are not required for regulator operation
and experimental results may allow them to be eliminated.
The input filter inductor may not be required because bulk
filter and bypass capacitors, as well as other loads located
on the board will tend to reduce regulator di/dt effects on
the circuit board and input power supply. Placement of the
power component to minimize routing distance will also
help to reduce emissions.
Figure 27: Filter components.
Figure 28: Input Filter.
Layout Guidelines
When laying out the CPU buck regulator on a printed cir-
cuit board, the following checklist should be used to
ensure proper operation of the CS5166.
1) Rapid changes in voltage across parasitic capacitors and
abrupt changes in current in parasitic inductors are major
concerns for a good layout.
2) Keep high currents out of sensitive ground connections.
Avoid connecting the IC Gnd (LGnd) between the source
of the lower FET and the input capacitor Gnd.
3) Avoid ground loops as they pick up noise. Use star or
single point grounding.
4) For high power buck regulators on double-sided PCBs a
single large ground plane (usually the bottom) is recom-
mended.
5) Even though double-sided PCBs are usually sufficient
for a good layout, four-layer PCBs are the optimum
approach to reducing susceptibility to noise. Use the two
internal layers as the +5V and Gnd planes, the top layer for
the power connections and component vias, and the bot-
tom layer for the noise sensitive traces.
6) Keep the inductor switching node small by placing the
output inductor, switching and synchronous FETs close
together.
7) The FET gate traces to the IC must be as short, straight,
and wide as possible. Ideally, the IC has to be placed right
next to the FETs.
8) Use fewer, but larger output capacitors, keep the capaci-
tors clustered, and use multiple layer traces with heavy
copper to keep the parasitic resistance low.
9) Place the switching FET as close to the +5V input capaci-
tors as possible.
10) Place the output capacitors as close to the load
as possible.
+
2
μ
H
1200
μ
F x 3/16V
33
1000pF
2
μ
H
T
J(MAX)
- T
A
Power
Thermal Management
1.2μH
×
14.2A
2.8V
L
×
Change in I
OUT
V
OUT
Application Information: continued
C
相關PDF資料 |
PDF描述 |
|---|---|
| CS5201-1GST3 | 1A Adjustable Linear Regulator |
| CS5201-1GDP3 | 1A Adjustable Linear Regulator |
| CS5201-1GDPR3 | 1A Adjustable Linear Regulator |
| CS5201-1 | 1A Adjustable Linear Regulator |
| CS5201-1GT3 | 1A Adjustable Linear Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS5168 | 功能描述:SCREWDRIVER,5/16"X8",SLOTTED 制造商:apex tool group 系列:* 零件狀態:在售 標準包裝:1 |
| CS5171/3_EVM_SEPIC | 制造商:P&S 功能描述:1.5 A 280 kHz/560 kHz Boost Regulators |
| CS5171BSTEVB | 功能描述:電源管理IC開發工具 CS5171/3 DEMO BD BOOST RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| CS5171BSTGEVB | 功能描述:電源管理IC開發工具 RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| CS5171ED8 | 功能描述:直流/直流開關調節器 1.5A High Efficiency RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。