- 您現在的位置：買賣IC網 > PDF目錄366891 > CR16HCT9VJE7 Microcontroller PDF資料下載
參數資料
| 型號： | CR16HCT9VJE7 |
| 英文描述： | Microcontroller |
| 中文描述： | 微控制器 |
| 文件頁數： | 75/157頁 |
| 文件大小： | 1256K |
| 代理商： | CR16HCT9VJE7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁當前第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
75
www.national.com
The interrupts can be individually enabled or disabled using
the Enable Transmit Interrupt (UnETI), Enable Receive Inter-
rupt (UnERI) and Enable Receive Error Interrupt (UnEER)
bits in the UnICTRL register.
A transmit interrupt is generated when both the UnTBE and
UnETI bits are set. To remove this interrupt, software must ei-
ther disable the interrupt by clearing the UnETI bit or write to
the UnTBUF register (thus clearing the UnTBE bit).
A receive interrupt is generated on two conditions:
1. Both the UnRBF and UnERI bits are set. To remove this
interrupt, software must either disable the interrupt by
clearing the UnERI bit or read from the UnRBUF register
(thus clearing the UnRBF bit).
2. Both the UnERR and the UnEEI bits are set. To remove
this interrupt the software must either disable it by clear-
ing the UnEEI bit or read the UnSTAT register (thus
clearing the UnERR bit).
18.2.8
A line break is generated when the BRK bit is set in the Un-
MDSL register. The TDXn line remains low until the program
resets the BRK bit.
A line break is detected if RDXn remains low for 10 bit times
or longer after a missing stop bit is detected.
Break Generation and Detection
18.2.9
Parity is only generated or checked with the 7-bit and 8-bit
data formats. It is not generated or checked in the diagnostic
loopback mode, the attention mode, or in the normal mode
with the 9-bit data format. Parity generation and checking are
enabled and disabled via the PEN bit in the UnFRS register.
The UnPSEL bits in the UnFRS register are used to select
odd, even, mark, or space parity.
Parity Generation and Detection
18.3
The software interacts with the USART by accessing the US-
ART registers. There are eight such registers:
— USART Receive Data Buffer (UnRBUF)
— USART Transmit Data Buffer (UnTBUF)
— USART Baud Rate Prescaler Register (UnPSR)
— USART Baud Rate Divisor Register (UnBAUD)
— USART Frame Select Register (UnFRS)
— USART Mode Select Register (UnMDSL)
— USART Status Register (UnSTAT)
— USART Interrupt Control Register (UnICTRL)
USART REGISTERS
18.3.1
The USART Receive Data Buffer is a byte-wide, read/write
register used to receive each data byte.
USART Receive Data Buffer (UnRBUF)
18.3.2
The USART Transmit Data Buffer is a byte-wide, read/write
register used to transmit each data byte.
USART Transmit Data Buffer (UnTBUF)
18.3.3
The USART Baud Rate Prescaler Register is a byte-wide,
read/write register that contains the 5-bit clock prescaler and
USART Baud Rate Prescaler (UnPSR)
the upper three bits of the baud rate divisor. This register is
cleared upon reset. The register format is shown below.
7
6
5
4
3
2
UnPSC
UnDIV10
UnPSC
Prescaler. This 5-bit field specifies the prescal-
er value used for dividing the system clock in
the first stage of the two-stage divider chain.
For the prescaler factors corresponding to
each 5-bit value, see Table 19.
UnDIV[10:8] Baud Rate Divisor (bits 10-8). This field con-
tains the three highest-order bits (bits 10, 9,
and 8) of the USART baud rate divisor used in
the second stage of the two-stage divider
chain. The remaining bits of the baud rate divi-
sor are contained in the UnBAUD register.
18.3.4
The USART Baud Rate Divisor Register is a byte-wide, read/
write register that contains the lower eight bits of the baud
rate divisor. This register contents are unknown upon power-
up and are left unchanged by a reset operation. The register
format is shown below.
USART Baud Rate Divisor (UnBAUD)
UnDIV[7:0]
Baud Rate Divisor (bits 7-0). This field contains
the eight lowest-order bits of the USART baud
rate divisor used in the second stage of the
two-stage divider chain. The three highest-or-
der bits are contained in the UnPSR register.
The divisor value used is the 11-bit UnDIV val-
ue plus 1.
18.3.5
The USART Frame Select Register is a byte-wide, read/write
register that controls the frame format, including the number
of data bits, number of stop bits, and parity type. This register
is cleared upon reset. The register format is shown below.
7
6
5
4
Reserved UnPEN UnPSEL UnXB9 UnSTP UnCHAR
USART Frame Select Register (UnFRS)
UnCHAR
Character Frame Format. This 2-bit field se-
lects the number of data bits per frame, not in-
cluding the parity bit, as follows:
00 = eight data bits per frame
01 = seven data bits per frame
10 = nine data bits per frame
11 = loopback mode; nine data bits per frame
UnSTP
Number of Stop Bits. This bit sets the number
of stop bits transmitted in each frame. If this bit
is 0, one stop bit is transmitted. If this bit is 1,
two stop bits are transmitted.
Transmit 9th Data Bit. This bit is the value of
the ninth data bit, either 0 or 1, transmitted
when the USART is configured to transmit nine
data bits per frame. It has no effect when the
USART is configured to transmit seven or eight
data bits per frame.
UnXB9
1
0
UnDIV9
UnDIV8
7
6
5
4
3
2
1
0
UnDIV7 UnDIV6 UnDIV5 UnDIV4 UnDIV3 UnDIV2 UnDIV1 UnDIV0
3
2
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| CR16HCT9VJE7Y | Microcontroller |
| CR16HCT9VJE8 | Microcontroller |
| CR16HCT9VJE8Y | Microcontroller |
| CR16HCT9VJE9 | Microcontroller |
| CR16HCT9VJE9Y | Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CR16HCT9VJE7Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT9VJE8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT9VJE8Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT9VJE9 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT9VJE9Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。