參數資料
型號： CPC5610ATR
元件分類： 通信、網絡模塊及開發工具
英文描述： Telecomm/Datacomm
中文描述： 電信/數據通信
文件頁數： 12/18頁
文件大小： 410K
代理商： CPC5610ATR
CPC5610/CPC5611
12
www.clare.com
Rev. 8.0
rent. The photocurrent, a linear representation of the
receive signal, is amplified and converted to a differen-
tial voltage output on RX+ and RX-.
Variations in gain are controlled to within ±1 dB by an
on-chip automatic gain control (AGC) circuit, which
sets the output of the photoamplifier to unity gain.
To accommodate single-supply operation, LITELINK
includes a small DC bias on the RX outputs of 1.0
Vdc. Most applications should AC couple the RX out-
puts as shown in Figure 6.
LITELINK may be used for differential or single-ended
output as shown in Figure 6. Single-ended use will
produce 6 dB less signal output amplitude. Do not
exceed 0 dBm into 600
(2.2 V
P-P
) signal input.
Figure 6. Differential and Single-ended Receive
Path Connections to LITELINK
Host-side CODEC
or Voice Circuit
3.3.2 Transmit Signal Path
Connect transmit signals from the host equipment to
the TX+ and TX- pins of LITELINK. Do not exceed a
signal level of 0 dBm in 600
(or 2.2 V
P-P
). Differen-
tial transmit signals are converted to single-ended sig-
nals in LITELINK. The signal is coupled to the transmit
photodiode amplifier in a similar manner to the receive
path.
The output of the photodiode amplifier is coupled to a
voltage-to-current converter via a transconductance
stage where the transmit signal modulates the tele-
phone line loop current. As in the receive path, gain is
set to unity automatically, limiting insertion loss to 0,
±1 dB.
Figure 7. Differential and Single-ended Transmit
Path Connections to LITELINK
LITELINK
Host CODEC or
Transmit Circuit
3.4 DC Characteristics
The CPC5610 and CPC5611 are designed for world-
wide application regarding DC characteristics, includ-
ing use under the requirements of TBR-21. The ZDC,
DCS1, and DCS2 pins control the VI slope character-
istics of LITELINK. Selecting appropriate resistor val-
ues for R
ZDC
(R16) and R
DCS
(R15) in the provided
application circuits assure compliance with DC
requirements.
3.4.1 Resistive Termination Applications
LITELINK includes a telephone line current limit fea-
ture that is selectable by selecting the desired value
for R
ZDC
(R16) using the following formula:
Clare recommends using 8.2
for R
ZDC
in North
America and Japan, limiting telephone line current to
133 mA.
3.4.2 Reactive Termination Applications
TBR-21 sets the telephone line current limit at 60 mA.
To meet this requirement, set R
ZDC
(R16) to 22.1
.
Guidelines for Effec-
ing in this application.
相關PDF資料
PDF描述
CPC5611A Telecomm/Datacomm
CPC5611ATR Telecomm/Datacomm
CPH3310
CPH3314 TRANSISTOR | MOSFET | P-CHANNEL | 30V V(BR)DSS | 1.6A I(D) | SOT-346
CPH3317
相關代理商/技術參數
參數描述
CPC5611 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:LITELINK⑩ II Silicon Data Access Arrangement (DAA) IC
CPC5611A 功能描述:固態繼電器-PCB安裝 LITELINK II, Full-wave Ring Detect RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT
CPC5611ATR 功能描述:固態繼電器-PCB安裝 LITELINK II, Full-wave Ring Detect, T/R RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT
CPC5620 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:LITELINK III Phone Line Interface IC (DAA)
CPC5620_1 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:LITELINK? III Phone Line Interface IC (DAA)
發布緊急采購，3分鐘左右您將得到回復。