- 您現在的位置：買賣IC網 > PDF目錄382908 > CPC5610ATR Telecomm/Datacomm PDF資料下載
參數資料
| 型號： | CPC5610ATR |
| 元件分類： | 通信、網絡模塊及開發工具 |
| 英文描述： | Telecomm/Datacomm |
| 中文描述： | 電信/數據通信 |
| 文件頁數： | 10/18頁 |
| 文件大?。?/td> | 410K |
| 代理商： | CPC5610ATR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
CPC5610/CPC5611
10
www.clare.com
Rev. 8.0
3. Using LITELINK
As a full-featured telephone line interface, LITELINK
performs the following functions:
DC termination
AC impedance control
V/I slope control
2-wire to 4-wire conversion (hybrid)
Current limiting
Ring detection
Caller ID signal reception
Switch hook
LITELINK can accommodate specific application fea-
tures without sacrificing basic functionality and perfor-
mance. Application features include, but are not
limited to:
High gain (+3 dBm) operation
Pulse dialing
Ground start
Loop start
Parallel telephone off-hook detection (911 feature)
Battery reversal
Line presence
World-wide programmable operation
This section of the data sheet describes LITELINK
operation in standard configuration for usual opera-
tion. Clare offers additional application information on-
line
(see Section 5 on page 14)
. These include informa-
tion on the following topics:
Circuit isolation considerations
Optimizing LITELINK performance
Data Access Arrangement architecture
LITELINK circuit descriptions
Surge protection
EMI considerations
Other specific application materials are also refer-
enced in this section as appropriate.
3.1 Switch Hook Control (On-hook
and Off-hook States)
LITELINK operates in one of two conditions, on-hook
and off-hook. In the on-hook condition the telephone
line is available for calls. In the off-hook condition the
telephone line is engaged. Use the OH control input to
place LITELINK in one of these two states. With OH
high, LITELINK is on-hook and ready to make or
receive a call. The snoop circuit is enabled. Assert OH
low to place LITELINK in the off-hook state. In the off-
hook state, loop current flows through LITELINK and
the system is answering or placing a call.
3.2 On-hook Operation
The LITELINK application circuit leakage current is
less than 10
μ
A with 100 V across ring and tip, equiva-
lent to greater than 10 M
on-hook resistance.
3.2.1 Ring Signal Detection via the Snoop
Circuit
In the on-hook state (OH and CID not asserted), an
internal multiplexer turns on the snoop circuit. This cir-
cuit monitors the telephone line for two conditions; an
incoming ring signal, and caller ID data bursts.
Refer to the application schematic diagram
(see Figure
3 on page 6)
. C7 (C
SNP-
) and C8 (C
SNP+
) provide a
high-voltage isolation barrier between the telephone
line and SNP- and SNP+ on the LITELINK while cou-
pling AC signals to the snoop amplifier. The snoop cir-
cuit “snoops” the telephone line continuously while
drawing no current. In the LITELINK, ringing signals
are compared to a threshold. The comparator output
forms the RING signal output from LITELINK. This sig-
nal must be qualified by the host system as a valid
ringing signal. A low level on RING indicates that the
LITELINK ring signal threshold has been exceeded.
For the CPC5610 (with the half-wave ring detector),
the frequency of the RING output follows the fre-
quency of the ringing signal from the central office
(CO), typically 20 Hz. The RING output of the
CPC5611 (with the full-wave ring detector) is twice the
ringing signal frequency.
Hysteresis is employed in the LITELINK ring detector
circuit to provide noise immunity. The setup of the ring
detector comparator causes RING output pulses to
remain low for most of the ringing signal half-cycle.
The RING output returns high for the entire negative
half-cycle of the ringing signal for the CPC5610. For
the CPC5611, the RING output returns high for a short
period near the zero-crossing of the ringing signal
before returning low during the positive half-cycle. For
both the CPC5610 and CPC5611, the RING output
remains high between ringing signal bursts.
The ring detection threshold depends on the values of
R3 (R
SNPD
), R6 (R
SNP-
), R7 (R
SNP+
), C7 (C
SNP-
), and
C8 (C
SNP+
). The values for these components shown
in the typical application circuits are recommended for
相關PDF資料 |
PDF描述 |
|---|---|
| CPC5611A | Telecomm/Datacomm |
| CPC5611ATR | Telecomm/Datacomm |
| CPH3310 | |
| CPH3314 | TRANSISTOR | MOSFET | P-CHANNEL | 30V V(BR)DSS | 1.6A I(D) | SOT-346 |
| CPH3317 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CPC5611 | 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:LITELINK⑩ II Silicon Data Access Arrangement (DAA) IC |
| CPC5611A | 功能描述:固態繼電器-PCB安裝 LITELINK II, Full-wave Ring Detect RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| CPC5611ATR | 功能描述:固態繼電器-PCB安裝 LITELINK II, Full-wave Ring Detect, T/R RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT |
| CPC5620 | 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:LITELINK III Phone Line Interface IC (DAA) |
| CPC5620_1 | 制造商:CLARE 制造商全稱:Clare, Inc. 功能描述:LITELINK? III Phone Line Interface IC (DAA) |
發布緊急采購，3分鐘左右您將得到回復。