參數資料
型號: COP8CCR9KMT8
廠商: National Semiconductor
文件頁數: 72/111頁
文件大小: 0K
描述: IC MCU EEPROM 8BIT 32K 56-TSSOP
標準包裝: 34
系列: COP8™ 8C
核心處理器: COP8
芯體尺寸: 8-位
速度: 20MHz
連通性: Microwire/Plus(SPI),UART/USART
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 49
程序存儲器容量: 32KB(32K x 8)
程序存儲器類型: 閃存
RAM 容量: 1K x 8
電壓 - 電源 (Vcc/Vdd): 2.7 V ~ 5.5 V
數據轉換器: A/D 16x10b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 56-TFSOP(0.240",6.10mm 寬)
包裝: 管件
其它名稱: *COP8CCR9KMT8
SNOS535I – OCTOBER 2000 – REVISED MARCH 2013
5.13.5 FRAMING FORMATS
The USART supports several serial framing formats (Figure 5-17). The format is selected using control
bits in the ENU, ENUR and ENUI registers.
The first format (1, 1a, 1b, 1c) for data transmission (CHL0 = 1, CHL1 = 0) consists of Start bit, seven
Data bits (excluding parity) and one or two Stop bits. In applications using parity, the parity bit is
generated and verified by hardware.
The second format (CHL0 = 0, CHL1 = 0) consists of one Start bit, eight Data bits (excluding parity) and
7/8, one or two Stop bits. Parity bit is generated and verified by hardware.
The third format for transmission (CHL0 = 0, CHL1 = 1) consists of one Start bit, nine Data bits and one or
two Stop bits. This format also supports the USART “ATTENTION” feature. When operating in this format,
all eight bits of TBUF and RBUF are used for data. The ninth data bit is transmitted and received using
two bits in the ENU and ENUR registers, called XBIT9 and RBIT9. RBIT9 is a read only bit. Parity is not
generated or verified in this mode.
The parity is enabled/disabled by PEN bit located in the ENU register. Parity is selected for 7- and 8-bit
modes only. If parity is enabled (PEN = 1), the parity selection is then performed by PSEL0 and PSEL1
bits located in the ENU register.
Note that the XBIT9/PSEL0 bit located in the ENU register serves two mutually exclusive functions. This
bit programs the ninth bit for transmission when the USART is operating with nine data bits per frame.
There is no parity selection in this framing format. For other framing formats XBIT9 is not needed and the
bit is PSEL0 used in conjunction with PSEL1 to select parity.
The frame formats for the receiver differ from the transmitter in the number of Stop bits required. The
receiver only requires one Stop bit in a frame, regardless of the setting of the Stop bit selection bits in the
control register. Note that an implicit assumption is made for full duplex USART operation that the framing
formats are the same for the transmitter and receiver.
Copyright 2000–2013, Texas Instruments Incorporated
Functional Description
63
Product Folder Links: COP8CBR9 COP8CCR9 COP8CDR9
相關PDF資料
PDF描述
COP8SAA716M8/NOPB IC MCU OTP 8BIT 1K 16-SOIC
CP2101-GMR IC CTRLR BRIDGE USB-UART 28MLP
CP2103-GMR IC CTRLR BRIDGE USB-UART 28MLP
CP2104-F03-GM IC SGL USB-TO-UART BRIDGE 24QFN
CP2105-F01-GM IC SGL USB-DL UART BRIDGE 24QFN
相關代理商/技術參數
參數描述
COP8CCR9LVA7 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
COP8CCR9LVA7/63 制造商:Texas Instruments 功能描述:
COP8CCR9LVA7/63SN 功能描述:閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
COP8CCR9LVA7/NOPB 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
COP8CCR9LVA763SN 制造商:National Semiconductor 功能描述:MCU 8-bit COP8 CISC 32KB Flash 5V 68-Pin PLCC