- 您現在的位置：買賣IC網 > PDF目錄16889 > COP8-PGMA-44QFP (National Semiconductor)PROGRAMMING ADAPTER PDF資料下載
參數資料
| 型號： | COP8-PGMA-44QFP |
| 廠商： | National Semiconductor |
| 文件頁數： | 20/62頁 |
| 文件大小： | 0K |
| 描述： | PROGRAMMING ADAPTER |
| 標準包裝： | 1 |
| 附件類型： | 編程適配器 |
| 適用于相關產品： | Cop 8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
8.0 Power Save Modes (Continued)
8.3 MULTI-INPUT WAKEUP
The Multi-Input Wakeup feature is used to return (wakeup)
the device from either the HALT or IDLE modes. Alternately
Multi-Input Wakeup/Interrupt feature may also be used to
generate up to 8 edge selectable external interrupts.
Figure 20 shows the Multi-Input Wakeup logic.
The Multi-Input Wakeup feature utilizes the L Port. The user
selects which particular L port bit (or combination of L Port
bits) will cause the device to exit the HALT or IDLE modes.
The selection is done through the register WKEN. The reg-
ister WKEN is an 8-bit read/write register, which contains a
control bit for every L port bit. Setting a particular WKEN bit
enables a Wakeup from the associated L port pin.
The user can select whether the trigger condition on the
selected L Port pin is going to be either a positive edge (low
to high transition) or a negative edge (high to low transition).
This selection is made via the register WKEDG, which is an
8-bit control register with a bit assigned to each L Port pin.
Setting the control bit will select the trigger condition to be a
negative edge on that particular L Port pin. Resetting the bit
selects the trigger condition to be a positive edge. Changing
an edge select entails several steps in order to avoid a
Wakeup condition as a result of the edge change. First, the
associated WKEN bit should be reset, followed by the edge
select change in WKEDG. Next, the associated WKPND bit
should be cleared, followed by the associated WKEN bit
being re-enabled.
An example may serve to clarify this procedure. Suppose we
wish to change the edge select from positive (low going high)
to negative (high going low) for L Port bit 5, where bit 5 has
previously been enabled for an input interrupt. The program
would be as follows:
RBIT
5, WKEN
; Disable MIWU
SBIT
5, WKEDG
; Change edge polarity
RBIT
5, WKPND
; Reset pending flag
SBIT
5, WKEN
; Enable MIWU
If the L port bits have been used as outputs and then
changed to inputs with Multi-Input Wakeup/Interrupt, a safety
procedure should also be followed to avoid wakeup condi-
tions. After the selected L port bits have been changed from
output to input but before the associated WKEN bits are
enabled, the associated edge select bits in WKEDG should
be set or reset for the desired edge selects, followed by the
associated WKPND bits being cleared.
This same procedure should be used following reset, since
the L port inputs are left floating as a result of reset.
The occurrence of the selected trigger condition for
Multi-Input Wakeup is latched into a pending register called
WKPND. The respective bits of the WKPND register will be
set on the occurrence of the selected trigger edge on the
corresponding Port L pin. The user has the responsibility of
clearing these pending flags. Since WKPND is a pending
register for the occurrence of selected wakeup conditions,
the device will not enter the HALT mode if any Wakeup bit is
both enabled and pending. Consequently, the user must
clear the pending flags before attempting to enter the HALT
mode.
WKEN and WKEDG are all read/write registers, and are
cleared at reset. WKPND register contains random value
after reset.
DS012838-27
FIGURE 20. Multi-Input Wake Up Logic
COP8SA
Family
www.national.com
26
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6037BAUKADJ+T | IC VREF SERIES ADJ SOT-23-5 |
| GCM24DTKD | CONN EDGECARD 48POS DIP .156 SLD |
| MAX6037BAUK30+T | IC VREF SERIES 3V SOT-23-5 |
| MAX6037BAUK25+T | IC VREF SERIES 2.5V SOT-23-5 |
| GBM30DTBN | CONN EDGECARD 60POS R/A .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP8-PGMA-48TF1 | 功能描述:插座和適配器 PROGRAMMING ADAPTER FOR 48TSSOP RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x |
| COP8-PGMA-49AF1 | 功能描述:插座和適配器 COP8TA PROGR. ADAPTOR RoHS:否 制造商:Silicon Labs 產品:Adapter 用于:EM35x |
| COP8-PGMA-56TF1 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Microcontroller with 8k Memory, Dual Op Amps, Virtual EEROM, Temperature Sensor,10-Bit A/D and Brownout Reset |
| COP8-PGMA-68P | 制造商:Texas Instruments 功能描述: |
| COP8-PGMA-68PF1 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS Flash Microcontroller with 8k Memory, Dual Op Amps, Virtual EEROM, Temperature Sensor,10-Bit A/D and Brownout Reset |
發(fā)布緊急采購，3分鐘左右您將得到回復。